ALERT: Miracle Paint is back in stock! CLICK HERE to order.
In this 24-minute instructional video, Kent shows you more than just how to change the transmission filter and the pan.
In this 19-minute detail instructions, Kent will show you how to get the old seal out, how to trial fit the new seal, and how to glue it in place properly. You can not believe how many seals we see that have not been installed properly.
In this detailed 22-minute video instruction, Kent will show you how to use his kit to perform a power drain on most 1965 to 1995 automatic transmission.
In this 15-minute video, Kent will show you step-by-step how to safely remove the Bowden cable without damaging it and how to install it to get the proper connection. This is not as easy as it looks, and you can break it if you are not careful.
In this 20-minute instruction video, Kent will show you how to take his short kit and combine it with a tester that you can purchase online to make a leak-free, reliable, and accurate fuel pressure tester for Bosch CIS fuel injection.
in this detailed 38-minute video Kent will walk you step-by-step through the procedures of removing the old belts, installing the new belts, and tightening them properly. When changing your V-belts there are other things you should consider replacing as well.
This video applies to both K-jetronic and KE-jetronic fuel injection engines on Mercedes from 1976 to 1993.. Let's say you just acquired an old gas engined Mercedes and you just can not get it to run right and or even get it to start.
In this 13-minute CIS training video, Kent will walk you through the steps recommended by Mercedes Benz to fully test the operation of the EHA valve on 1984 to 1993 4, 6, and 8-cylinder engines with KE-jetronic fuel injection.
After completing the pressure test on your CIS engine, you discover a problem. But how can you find out how to isolate and fix it? This is going to require some research on your part. Start by learning how the system works and how each component plays a part.
In this video, you will see how the gauges are hooked up to a 560SL and how the pressures are read. The length of this 30-minute shows the detail Kent has put into filming all the critical components of doing a KE-Jetronic fuel system pressure test.
This video is specific to K- jetronic fuel-injected engines from 1976 to 1985. This includes the 350, 450, and 280 engines in the R107, W116, W123, and early W126 gas Mercedes. In this 29-minute video. Kent will show you how to hook up the gauge, run the fuel pumps, and complete the test.
There are a few factory recommend procedures and tests you should do before you do an actual pressure test on a CIS fuel-injected engine. In this 20-minute training video, Kent will walk you through these procedures step-by-step.
To do proper system testing on CIS fuel injection, you must find a way to get the fuel pump or fuel pumps to run continuously without the engine running. This can not be done by just using the ignition key. In this 15-minute training video, Kent will show the options available to do this.
This video will help you decide if you want to try to do a fuel pressure test yourself. It is a fairly simple DIY job but will all the confusion and misinformation on the internet; one would believe it is a complicated process that is hard to understand.
People call these two units pressure regulators, but really only one of them is. In this xx minute video, Kent will explain how these are different, what each one does, how to adjust them, and how to test them with a hand pump vacuum tester.
In this 8-minute video, Kent will show you how to quickly depressurize your D-Jetronic fuel system before doing any injector service, replacing any hoses, or hooking up our fuel pressure tester.
In this xx minute instructional video Kent will walk you through the process of hooking up the gauge, taking the proper readings at idle and at rpm, adjusting the regulator, checking for internal leaks, and depressurizing before removal.
In this 12-minute instructional video, Kent will show you how he installs the rear hood seal on the hoods of the R107 and the C107 built from 1972 to 1989.
In this 30 minute instructional video Kent will use a 1972 300SEL 4.5 to show you how to remove the master cylinder with minimal spillage, how to install the tank and bench bleed a new master cylinder, and how to reinstall it with minimal brake fluid spillage while protecting your car's paint.
Here is a 15 minute video that can really help you if you have small coolant leaks around your idle air valve. You will learn how easy it is to break the bolts when removing this valve, and your option to fix it.
In this 14 minute instructional video Kent will demonstrate how to remove and install a new thermostat in a 450 engine. Here you will see how tight it is to get install in a 300SEL 4.5, but other V8s will have better access.
In this 12 minute instructional video, Kent will demonstrate how to remove and replace the viscous fan clutch in a 1972 300SEL 4.5. Other topics covered will be cleaning and corrosion prevention. This video is included free with the purchase of our fan clutch install kit ( see below).
In this 33-minute instructional video, Kent will show you how to convert your old points ignition to an efficient modern electronic ignition. Rid yourself of those old high-maintenance distributor points forever.
Also covers 1980 W116 sedans. In this 20-minute instructional video, Kent will walk you through the steps of getting the steel sunroof panel installed properly back into the car's roof. The first step will require cleaning, inspection, and possible replacement of the plastic slides.
In this 23 minute highly detailed video Kent will show you to reasons why and some of the problems you will run into when you change these hoses on your own D-Jet engine. He will take the new parts and show you how to properly install them using the correct hose clamps, sealants and lubes.
Also covers 1980 W116 sedans.
In this 36-minute instructional video, Kent will walk you through the process of doing a complete fuel hose replacement and fuel injector service on a 1970 to 1975 Mercedes V8 engine with Bosch EFI electronic fuel injection.
In this 9 minute instructional video, Kent will explain how to test your fuel accumulator to determine whether or not it has failed internally. A failed accumulator will make your engine hard to start when hot.
In this 24 minute instructional video Kent will explain the process of how to bench clean and test your D-jetronic fuel injectors in your own garage or workshop once they are removed from the engine.
In this 26 minute instructional video Kent will show you how to hook up a CIS fuel pressure tester to your older K-jectronic gas engine.
In this 10 minute instructional video Kent will explain why you want to "jump" your K-jet fuel pump relay, how to do it, how to find the location in you car, and why he prefers to have a long "switchable" jumper.
This xx minute video will take you step by step through the process of modifying your warm up regulator so you will be able to easily make adjustments to your cold start control pressure.
This 25 minute video will instruct you on how to replace the fuel injectors in your 1976 to 1980 8-cylinder M117 engine safely and efficiently. This is a fairly straightforward job, but there are some pitfalls you will want to avoid.
This 33 minute video will instruct you on how to replace the fuel injectors in your 8-cylinder M116 engine safely and efficiently. This is a fairly straightforward job, but there are some pitfalls you will want to avoid.
This 16-minute video will instruct you on how to replace the fuel injectors in your 6 cylinder M110 safely and efficiently. Since this is a fairly straight forward remove and replace this is not a step-by-step video.
Is your old gas engine running a little rough? There could be lots of reasons for this but if you have good compression, good plugs and wires you might consider replacing your O2 sensor even if your warning light is not showing up. This is an easy DIY job.
In this 13 minute instructional video Kent will demonstrate how to remove an old fan clutch and replace it with a new one on a 1983 380SL This is a beginner D.I.Y. job and no special tools are required. This video is included free of charge with the purchase of our Later V8 fan clutch kit.
In this detailed 30-minute video Kent will walk you through the process of installing new tie rod ends on his 1959 Mercedes 220SE. The principles are the same on almost all models from the 1950s up to the 1990s. He will explain the differences in adjustment between the older and newer styles
In this 30-minute instructional video, Kent will explain how this new pump compares to the original, what is included in the kit and why, how to make a new plugin wiring harness, demonstrate step by step how to install this pump in a late W123 and explain the differences you will face when instal
In this instructional video, Kent demonstrates how easy it is to install the Klima heater control valve ( monovalve replacement ). If you have one of these popular and classic Mercedes, this is the best upgrade you can make for your climate control.
This an instructional "how-to" video that comes with our ACCIII performance upgrade it. It will show you how to install a protective fuse for your auxillary water pump and how to replace the rotton foam climate control hose under your dash. Total run time is 16:29.
Please note that this video class is included free with the purchase of one of our remaining new 450SL or 380SL steering lock assemblies.
To many people, automotive electrical systems and testing are a big mystery. It is not as complicated as you might think.
In this video, Kent will show you how he fixed his leaking tires on his chrome alloy wheels by using Miracle Paint. This is a full 22-minute step-by-step instructional video. Watch the video "trailer" below to give you a better understanding of what is involved in this procedure.
This video will show you how to remove the front crank seal race using the factory tool and using Kent's custom puller. It will also demonstrate a very easy way to install a new replacement race before installing a new seal.
Kent will get right up behind the rear end hub plate and show you close up how to remove and replace a sway bar link. This is not a difficult job especially if you follow the sequence shown in this 7- minute video.
In this 13-minute video instruction Kent will show you how to make your own accumulator tee hose connection either using parts from. our kit ( see below) or parts you purchase yourself. This video is included free with the purchase of our kit.
Kent will take you over to his workbench and completely take apart a rusty and old fuel delivery system from a 1980 450SL and put it all back together again with some shiney new paint and parts supplied in his special kit for these cars. This video runs for 24 minutes.
In this 30 minute-long video Kent will walk you through what he did for the rear suspension on his 1983 240D.
In this 46 minute very detailed step-by-step video instruction, Kent will show you how to remove the fuel delivery system from your 1986 to 1991 420SEL, 300SE, 300SEL, 560SEL, 560SL, and 560SEC, take it over to your bench and take it all apart, install new pumps, filter, accumulator, and hoses, t