ALERT: Miracle Paint is back in stock! CLICK HERE to order.
In this 30 minute-long video Kent will walk you through what he did for the rear suspension on his 1983 240D.
Brand new aftermarket fuel accumulator for the 1986 to 1991 V8 engines. It is mounted near the fuel filter under the back end of the car and hardly ever gets replaced. What does it do and how do you know if it is bad.
Also will work on (some but not all) 1976 to 1980 280SE, 280SEL, 280SL and 280E. Brand new aftermarket fuel accumulator for the 1976 to 1985 V8 engines. It is mounted near the fuel filter under the back end of the car and hardly ever gets replaced.
In this 46 minute very detailed step-by-step video instruction, Kent will show you how to remove the fuel delivery system from your 1986 to 1991 420SEL, 300SE, 300SEL, 560SEL, 560SL, and 560SEC, take it over to your bench and take it all apart, install new pumps, filter, accumulator, and hoses, t
This 17-minute video will cover the removal of an old Hirschmann power antenna and then Kent will show you how to troubleshoot the wiring plug in the car to see if you are getting proper power back to the antenna. No sense in replacing a faulty antenna until you make sure your wiring is OK!
DOES NOT INCLUDE ANY METAL FACTORY HARD LINES!!! What you SEE in the picture is exactly what you will receive. Many of these particular big V8 models are now becoming true collector cars and going up in value at a steady rate.
In this xx-minute long video, Kent will show you how to install our aftermarket power antenna in your 116, 123, or 123 sedan or coupe. Removal of your old antenna is not covered in this on-demand video but it is very straightforward once you remove the inner fender well panel.
Power Hirschmann antennas are no longer available new. It is possible to remove and repair the old Hirschmanns if you are willing to dig in and spend time cleaning, adjusting, lubing, etc.
It was difficult to find a filter to fit the correct size outlet hose. Install this steel 10-micron filter in your fuel tank outlet hose to protect your fuel pump. Clamps are provided along with a pull to plug the fuel hose temporarily to reduce fuel spills.
A brand new set of two grease caps as shown by Febi. Time to get rid of those ugly beat up and dented grease caps.
Doing a compression test is one of the best ways to determine the internal health of your gas engine. This is a primary test for doing a physical examination. You want to do this on any old Benz before spending a lot of money to get the engine running right or before restoring your car.
You might be surprised to realize you spark plug holes need cleaning - and yes some REALLY need cleaning! This 5-minute video will demonstrate Kent's method of cleaning the threads in the cylinder.
This video will walk you step-by-step through the proper procedures for doing a full compression test on your older V8 Mercedes Engine.
This video is loaded with tips on how to properly lubricate all the key components that make your sunroof operate smoothly and properly. It is NOT a complete manual on everything related to sunroofs. It will NOT show you all the details to get the sunroof out and back in.
Emergency brake shoe maintenance is often neglected because the rear brake disc / rotor has to be removed to inspect and repair them. If the car has ever been driven a long distance with the emergency brake on, expect problems.
Whether your just changing pads, hoses, or doing a complete brake system overhaul, the items we include in this DIY will guarantee the job gets done with no mistakes, minimum frustration, and lasting results. There is no other kit like this anywhere.
This manual is a complete guide for all brake component replacement for all 1965-1995 Mercedes Benz cars. It will help you identify common signs of trouble, inspecting brake components, and replacing major brake components - a necessity for any DIY brake job on your Mercedes Benz!
In this 22-minute instructional video, Kent will take you inside the door on a W123 240D and show you all the key points that should be lubricated and the type of lubricants you should use.
This is a very common problem on the W123. The wood will just fall off someday. Worse when the car is left outside or in a hot climate.
Replacing a distributor cap is easy right. No problem?? If it were I would not get so many emails and why the engine won't run right after changing the cap and rotor. This is a short eight and a half minute video but the tips I share could save you some big headaches.
Diesel idling too fast. Diesel idling too slow. Diesel shaking at idle. Transmission jerks with shifting from Park to Drive. These are some of the symptoms that might indicate your engine's idle speed is not adjusted correctly.
This on-demand instructional video was filmed to go with Kent's new fuel tank sending unit service kit launched in June of 2020. This is not a complete video on the subject of fuel level sending units. For the complete video see related products below.
If your fuel gauge stops working or is not reading accurately, many times it can be repaired by removing it from the fuel tank, taking it apart and giving it a good internal cleaning of the contact points, float shaft, and wires.
We have been talking about this for years. It was Ryan who got a friend to make this for us. It is a very high-quality vinyl with a special stick adhesive that "breathes" and does not allow bubbles to get trapped during application.
This 11-minute instructional video will show you how to set up and use a digital tach to check the idle speed of your diesel engine and how to use the tools in Kent's kit to adjust the idle speed on 1977 to 1985 four and five-cylinder diesels ( not 190D ).
Diesel idling too fast. Diesel idling too slow. Diesel shaking at idle. Transmission jerks with shifting from Park to Drive. These are some of the symptoms that might indicate your engine's idle speed is not adjusted correctly.
This 23-minute video will demonstrate how Kent repairs some small rust spots inside the fender wells of a W116 sedan. Disclaimer: This method of repair is not recommended for large rust holes under the car or for holes that have been caused by road salt.
When the motor won't move the window down you can not get to the bolts that hold the regulator to the glass. So then how can you get it out of the door! What a pain! In this xxx minute video Kent will show you what you need to do in order to get a "stuck" power window regulator out of a door.
Fuses, supplies, and video instructions (below) to restore most older fuse boxes to better than original condition.
Fuses, supplies, tools and video instructions (below) to restore most older fuse boxes to better than original condition.
Hard to find not torn or damaged in some way. These fit on the lips of the front under fender plastic splash guards. No tears or rips - rubber is still soft - good cleaning and sealing with rubber protectant needed.
PLEASE read the instructions below carefully on how you will view this video. It is NOT downloaded to your computer and viewing is NOT automatic. You must be logged in at Mercedessource.com and you MUST click on "my account".
Hard to believe we took so long to come up with this tool. It was Gerson's genius that made it happen. The secret turned out to be the hook that keeps the tool in place while stretching out the rubber donut. Wow! What a cool tool.
Socket is now black (impact grade). This is a tool that Kent first thought about making 20 years ago. While installing shock absorbers in his 380SL he had finally had enough - so it was back to the machine shop to come up with a new tool.
In this video, Kent will show you how to safely and cleanly remove the fuel from the tank on your older Benz. You will need to drain the fuel anytime you replace the back end hoses, the tank filter screen, the fuel pump or the fuel filter.
Hard to believe we took so long to come up with this tool. It was Gerson's genius that made it happen. The secret turned out to be the hook that keeps the tool in place while stretching out the rubber donut. Wow! What a cool tool.
Good used rocker arm assemblies as shown. This is the actual set you will receive.
These are very high-quality brake pads and fit many different models. Brake pad paste included. Watch the video below to see why these are Kent's favorites.
These are simply the best for your old Benz. They fit all W126 300SD and R107 380SL from 1981 to 1985. They also will fit the W126 380SE, 380SEL, and 500SEL from 1981 to 1985. Very heavy to ship. Watch the video below to see why these are Kent's favorites.
Works on the following: 6 cylinder gas MFI engines 1959 to 1972, 6.3 and diesel engines 200D 220D 240D 300D 300TD 300CD and 300SD through 1985.
You want superior stopping performance as well as minimum brake dust on your wheels - then these pads are what you want. Watch the video below - they are also really pretty! :-)
Watch the video below to see how this special wrench is used on the three nuts holding the exhaust downpipe to the turbocharger exhaust flange.
When replacing the thermostat in your order diesel you may end up fitting a lot of corrosion. This kit will help you make sure you do not have any leaks when you install the new thermostat and will prevent corrosion of the housing bolts in the future.
This is a hard-to-find adapter that will need if you have one of the early 1990s 5 and 6 cylinder turbo diesel engines. We machine this right here in our shop and it is designed to work directly with our OM61x compression tester ( see related products below):
Have you ever had a hard time finally a very small coolant leak? Do you find yourself adding small amounts of coolant but can not see any leak? Is there a funny smell coming from inside your Benz when you run the heater?
In this video, Kent will walk you through the steps needed to convert your older Brake Bleeder tank to one that can continue to bleed brake systems as well as pressure test radiators and cooling systems.
This easy-to-install kit could do wonders for your older diesel engine. The lift pump is almost always forgotten when it comes to maintenance on the OM616 and OM617 engines.
If you are experiencing hard starting or unexplained loss of power, your engine's lift pump could be failing.
Many uses for this quality hard steel tool including removing W123 and early W126 motor mount bolts.
This plate is often corroded and pitted. The locking tabs are usually rusted away. And the original alloy nuts are often rounded off. This is not perfect but way better than most.