Search | W201

I have used a lot of different clamping tools over the years to prevent fluids from leaking out when removing coolant, fuel, or brake fluid hoses. Most work ok. Some are hard to use in tight places.  Many do not stop every last drip from coming out of the hose.

This set of 5 pick tools have very thin and sharp points. Best set Kent has found to remove orings in hard to get to locations. The variety of angles available allows you to get into almost anywhere to remove and o-ring, sealing ring or other small part.

Works on 110, 115, 116, 123, 201, 126 and 124 diesel engines 200D 220D 240D 300D 300CD 300TD 300SD 190D 300SDL. We have found that over half of the deep sockets we test will not go over some of the longer injectors.

This inexpensive kit will allow you to replace the old hardened and brittle fuel hose in your 601 602 or 603 diesel's engine compartment as well as those old worn out factory clamps with new high quality worn gear clamps that will not cut into the rubber hose.

Every one of these pumps I have ever seen needs resealing. The seals and o-rings become just too hard over all those years of use. This is the most complete SLS (self-leveling suspension) pump overhaul kit on the market today.

Use this special swedge fittings when making any type of copper coil coolant heater for our SVO WVO fuel system. One end of this fitting clamps down tight on the copper pipe and the other end can accept any standard fitting with 1/4 inch male national pipe thread.

Bad rear mount can cause excessive engine vibration. No instructions included at this time.

Fits 190D, 190E, 260E, 300CE, 300D, 300E, 300SDL, 300SL, 300TD, 300TE, 350SD, 350SDL, 500SL, E300, E320, SL320, SL500

I like the convenience of using the factory jack points (holes) but I absolutely DO NOT like using the factory jack - except in cases of emergency road side repair. You all know it can be a little unstable... I solved this problem by using a large heavy duty bolt.

This is the new Bosch plastic upgrade to replace the old metal style fuel stop solenoid or shutoff valve. This is located on the top rear section of the injection pump (right under the intake manifold). Sorry, no instructions included but it is a straight forward replacement.

When using a pencil glow plug reamer, this modified 12 mm wrench will allow you to PUSH in on the reamer while turning - and let me tell you - this is needed when you have heavy carbon buildup in the prechambers.

High quality lubricant to be used when assembling bearings in engines or in components that are oiled by engine oil. This WILL prevent scoring and wear upon initial start-up after overhaul.

Genuine MBZ Part with wiring plug for later models: Please note this buzzer is really for the 1985 and later models. The wiring pigtail is not used on pre-1985 steering locks. The switch itself is the same but for older models you will have to install and leave the pigtail connected.

This must-have kit does not only have hard-to-find metric sizing, but the o-rings are made out of nitrile which holds up better to heat and is more resistant to oil, grease, hydraulic fluid, silicone and even water.

We receive a large number of emails from customers complaining about small fuel leaks at the fuel injector housing (coming out the threads between the two halves)and how best to seal them. To fix this high pressure leak requires taking the injector apart and "lapping" the mating surfaces.

Includes 1 meter of nylon braided clear windshield washer hose. No instructions included.

CLICK HERE to view the complete windshield washer squirted kit.

Dont neglect this service as many do! I recommend the hydraulic fluid and filter be changed every 30,000 miles. You would not believe how many SLS vehicles I have seen with dirty hydraulic fluid - I mean nasty!  Sometimes I have even found engine oil in the system!

Here are the correct size metric nuts with built in shoulder washer. If you drop these in behind the injection pump you may never find them. When doing glow plug service it is always a good idea to have some spare nuts on hand. New Bosch glow plugs do not come with new nuts.

Some of those early fuel injections systems can be troublesome. If you don't understand the system or how it works you will never be able to troubleshoot it successfully. This manual explains the different comp0nents in the system, their purpose, and how they interact together.

Brand new Meyle front Strut. Fits 190E 2.3 and 190D 2.2 and 190E 2.6

these years and models -- application notes:

Fits all 190E 190D 300E 300CE Etc. from 1984 to 1993

NEW Genuine Mercedes Modulator Cap. Check to see if yours is cracked. Cap removal is required for modulator adjustment.

Typical old and cracked rubber cap:

Fits all 110 111 113 108 107 116 114 115 123 126 201 124 129 140 early 60's to late 90's

Another High Quality product from Lubro Moly. This is a 300ml can of Motor Oil Saver. It Rejuvenates rubber and plastic engine seals and reduces oil consumption via the piston rings and valve guides; counteracts the loss in viscosity of motor oils.

Another high quality product made by Lubro Moly. This is a 50g tube of Gear oil additive. It is a concentrated moly based treatment for manual shift transmissions, differentials, steering boxes, transaxles, and rear axles. Reduces Gear noise and whine, smooths shifting.