ALERT: Miracle Paint is back in stock! CLICK HERE to order.
This is a quality aftermarket part and an excellent alternative to a used one. New O.E. is no longer available.
To many people, automotive electrical systems and testing are a big mystery. It is not as complicated as you might think.
These are the best wires you can get for your 1981 to 1985 380SL 380SLC 380SE 380SEL 380SEC and 500SEL. The coil wire is included. Consider replacing your cap, rotor, and CORRECT spark plugs at the same time. See related products below:
In this video, Kent will show you how he fixed his leaking tires on his chrome alloy wheels by using Miracle Paint. This is a full 22-minute step-by-step instructional video. Watch the video "trailer" below to give you a better understanding of what is involved in this procedure.
This kit was developed by Kent primarily to fix leaking chrome wheels. The free on-demand video that comes with this kit shows the detailed process of cleaning and filling the corroded areas along the edges of the inside of the wheel to seal them and stop annoying tire leaks.
We are not kidding when we say to get them while you can. Genuine Mercedes replacements are now at $500. When you see prices go up like this you know that supply may be dwindling.
This video will show you how to remove the front crank seal race using the factory tool and using Kent's custom puller. It will also demonstrate a very easy way to install a new replacement race before installing a new seal.
This hose assembly was used on the fuel delivery systems in the late 1970s and early 1980s. Installed on some R107 450SL and 450SLC, W116 450SE / L and 280SE, and the W123 280E and 280CE. Be sure to check your car before ordering to make certain this hose is installed.
Kent modified this puller and developed a procedure to remove the front crank seal race so the job could be affordable from the DIY mechanic. This costs less than half the cost of the factory tool.
Two new wing nuts. These have wider wings so they are easier to loosen and tighten. Replace the nut that most people install after the wing nut has been lost!
PDF DOWNLOAD FINALLY AVAILABLE of our popular 'Preventing Catastrophic V8 Engine Failure' Manual!!
Applies to the following chassis: 111, 108, 109, 107, 116, and 126. Includes 3.5, 4.5, 350, 380, 450, 500, 420, and 560 V8 engines from 1970 to 1991.
Kent will get right up behind the rear end hub plate and show you close up how to remove and replace a sway bar link. This is not a difficult job especially if you follow the sequence shown in this 7- minute video.
In this 13-minute video instruction Kent will show you how to make your own accumulator tee hose connection either using parts from. our kit ( see below) or parts you purchase yourself. This video is included free with the purchase of our kit.
This kit will give you everything you need to fix the leaking or aged Tee hose between the fuel damper and the fuel accumulator on most 1977 to 1980 fuel delivery systems. Watch the video below to learn why this is needed.
Kent will take you over to his workbench and completely take apart a rusty and old fuel delivery system from a 1980 450SL and put it all back together again with some shiney new paint and parts supplied in his special kit for these cars. This video runs for 24 minutes.
In this 30 minute-long video Kent will walk you through what he did for the rear suspension on his 1983 240D.
Brand new aftermarket fuel accumulator for the 1986 to 1991 V8 engines. It is mounted near the fuel filter under the back end of the car and hardly ever gets replaced. What does it do and how do you know if it is bad.
Also will work on (some but not all) 1976 to 1980 280SE, 280SEL, 280SL and 280E. Brand new aftermarket fuel accumulator for the 1976 to 1985 V8 engines. It is mounted near the fuel filter under the back end of the car and hardly ever gets replaced.
In this 46 minute very detailed step-by-step video instruction, Kent will show you how to remove the fuel delivery system from your 1986 to 1991 420SEL, 300SE, 300SEL, 560SEL, 560SL, and 560SEC, take it over to your bench and take it all apart, install new pumps, filter, accumulator, and hoses, t
This 17-minute video will cover the removal of an old Hirschmann power antenna and then Kent will show you how to troubleshoot the wiring plug in the car to see if you are getting proper power back to the antenna. No sense in replacing a faulty antenna until you make sure your wiring is OK!
R107 power Hirschmann antenna are no longer available new. It is possible to remove and repair the old Hirschmann antenna if you are willing to dig in and spend time cleaning, adjusting, lubing, etc.
In this 30-minute instructional video, Kent will walk you through the steps to remove your old antenna, test and troubleshoot your wiring plug coming to the antenna, and install our aftermarket antenna using the special wiring connectors we include in the kit.
DOES NOT INCLUDE ANY METAL FACTORY HARD LINES!!! What you SEE in the picture is exactly what you will receive. Many of these particular big V8 models are now becoming true collector cars and going up in value at a steady rate.
It was difficult to find a filter to fit the correct size outlet hose. Install this steel 10-micron filter in your fuel tank outlet hose to protect your fuel pump. Clamps are provided along with a pull to plug the fuel hose temporarily to reduce fuel spills.
All 380SL, 380SE, and 380SEL owners take note. Even if you acquire a nice 380 like Kent's Cherry you are going to need some or all of these components ( unless of course it was recently done by a competent mechanic ).
PLEASE LOOK AT YOUR SYSTEM BEFORE ORDERING to confirm the type of accumulator you have. ( Watch the last video below for examples )For systems with ONE HOLE ACCUMULATOR only. Some 450SL, 450SLC, 450SE, 450SEL with 4.5 and W116 280SE .
In this 28-minute instructional video Kent with show you how to do a compression test on your own Mercedes gas engine and explain how to interpret the results. It is very important you do this procedure BEFORE "throwing" parts at your engine trying to fix a performance problem.
Doing a compression test is one of the best ways to determine the internal health of your gas engine. This is a primary test for doing a physical examination. You want to do this on any old Benz before spending a lot of money to get the engine running right or before restoring your car.
You might be surprised to realize you spark plug holes need cleaning - and yes some REALLY need cleaning! This 5-minute video will demonstrate Kent's method of cleaning the threads in the cylinder.
This video will walk you step-by-step through the proper procedures for doing a full compression test on your older V8 Mercedes Engine.
Emergency brake shoe maintenance is often neglected because the rear brake disc / rotor has to be removed to inspect and repair them. If the car has ever been driven a long distance with the emergency brake on, expect problems.
Whether your just changing pads, hoses, or doing a complete brake system overhaul, the items we include in this DIY will guarantee the job gets done with no mistakes, minimum frustration, and lasting results. There is no other kit like this anywhere.
This manual is a complete guide for all brake component replacement for all 1965-1995 Mercedes Benz cars. It will help you identify common signs of trouble, inspecting brake components, and replacing major brake components - a necessity for any DIY brake job on your Mercedes Benz!
In this 22-minute instructional video, Kent will take you inside the door on a W123 240D and show you all the key points that should be lubricated and the type of lubricants you should use.
Replacing a distributor cap is easy right. No problem?? If it were I would not get so many emails and why the engine won't run right after changing the cap and rotor. This is a short eight and a half minute video but the tips I share could save you some big headaches.
This is one of those severely neglected parts that seems never to get changed. This is the FIRST thing you want to look at when the engine won't start, starts and quits, or misfires erratically. This is a quality German-made Bremi aftermarket cap.
This highly detailed 24-minute DIY video instruction will show you how to do the following on your EFI R107: Inspect the rear hoses for fuel leaks, drain the fuel out of your fuel tank, take the fuel pump and filter assembly apa
Since new original style pumps are no longer made, this is the best way to finally fix your old fuel pump leaks and poor performance.
If your V8 is running hot or temp gauge is moving you may have a bad sending unit. Located at the front of the engine. Easy replace. Drain one gallon of coolant out of the radiator before removing it.
This on-demand instructional video was filmed to go with Kent's new fuel tank sending unit service kit launched in June of 2020. This is not a complete video on the subject of fuel level sending units. For the complete video see related products below.
If your fuel gauge stops working or is not reading accurately, many times it can be repaired by removing it from the fuel tank, taking it apart and giving it a good internal cleaning of the contact points, float shaft, and wires.
We have been talking about this for years. It was Ryan who got a friend to make this for us. It is a very high-quality vinyl with a special stick adhesive that "breathes" and does not allow bubbles to get trapped during application.
This 23-minute video will demonstrate how Kent repairs some small rust spots inside the fender wells of a W116 sedan. Disclaimer: This method of repair is not recommended for large rust holes under the car or for holes that have been caused by road salt.
When the motor won't move the window down you can not get to the bolts that hold the regulator to the glass. So then how can you get it out of the door! What a pain! In this xxx minute video Kent will show you what you need to do in order to get a "stuck" power window regulator out of a door.
Fuses, supplies, and video instructions (below) to restore most older fuse boxes to better than original condition.
Fuses, supplies, tools and video instructions (below) to restore most older fuse boxes to better than original condition.
Fits all 380SL and 380SLC from 1981 to 1985. This flexible fuel hose connects the outlet of the fuel filter to the metal hard fuel line going from the rear of the 380SL to the engine compartment. This hose is hard to install and hard to inspect.
Note that this video is free of charge when you purchase our 380SL rear fuel hose replacement kit ( see related products below).
PLEASE read the instructions below carefully on how you will view this video. It is NOT downloaded to your computer and viewing is NOT automatic. You must be logged in at Mercedessource.com and you MUST click on "my account".
High-quality fuel filter for your later model R107 SL. With the right tools and knowledge, you may not need to drain your fuel tank to replace this filter ( replacement should be every 30,000 miles for peak performance. Watch Kent's video below for installation tips.