ALERT: Miracle Paint is back in stock! CLICK HERE to order.
Includes Kent's four detailed videos on every aspect of this job! This is now becoming one of the most common oil leaks in 1968 to 1985 diesel engines. Let's face it.
If your 60x diesel engine has more than 150,000 miles you might want to consider changing the time chain. If that critical chain breaks at high speed it could destroy your engine.
If your 103 engine makes ticking noises when you first start it up and that noise comes and goes it may be due to one or more failed hydraulic valve lifters.
When replacing your 103 engine timing chain it is also important to replace the chain tensioner.
Don't lose your high mileage (above 150,000 miles) 103 engine due to a failed timing chain. If this chain breaks at high speed it can destroy the engine.
New valve cover gasket. Common source of engine oil leaks. Must be replaced any time you remove the valve cover. Fits all 103 engines 1986 to 1993. No instructions included.
If you are experiencing high oil consumption and excessive engine smoke with your 6 cylinder 190E or 300E (CE and TE) or 126 300SE / L with the single cam 103 engine this is most likely what you need to fix the problem.
Good used turbo charger center section oil system outlet drain pipe tube as shown. This only fits the Garret T3 Turbo. Will not fit the KKK turbos. Will not fit 1985 models with trap oxidizer.
This is that little vacuum valve that always gets it nipples broken off... It is located right behind your thermostat housing on the 1981 to 1985 turbo diesel engines. It controls vacuum going to your EGR valve.
2007-12-05ALERT! Before you replace your suspected failing brake booster you might want to change the o-ring seal between the master cylinder and booster first.
Factory fuel hose that goes from the fuel tank strainer to the metal feed pipe just above your rear axle. Fits all 116 diesel 300SD, and 123 240D 300D and 300CD and all 126 chassis diesels 300SD 300SDL 350SD/L.
If you need everything for your front hub, then this is the best deal. This kit is for BOTH sides. Comes with inner and outer wheel bearings, seal, cap, ground clip, and a tube of FREE HIGH PERFORMANCE synthetic wheel bearing grease.
New front INNER wheel bearing with race for one side only. Fits right or left side on 116, 123 and 126 chassis, 240D 300D 300TD 300CD 300SD from 1977 to 1984. PLEASE NOTE: WILL NOT FIT MODELS WITH ABS.
Fits 116 123 126 4 and 5 cylinder non turbo and turbo engines 1977 to 1985. Good used set of five special factory stretch bolts that hold the rocker arm towers to the cylinder head. Common damaged item and hard to find new. The 5 bolts here will work with 5 cylinder engines.
Long drive pin punches are very handy when working on your Benz. The smaller size in this set is particularly helpful when removing and replacing twin pin style brake pads. All steel. Made in India. Pin sizes: 1/8'', 3/16'', 1/4'', 5/16'' and 3/8''
New metal end piece with set screw that connects to the linkage on valve cover on 1977 to 1979 300D CD and 240D. Check your cable for an exact match before ordering. This piece always seems to get lost and can be hard to find.
New front outer wheel bearing with race for one side only. Fits right or left side on 116, 123 and 126 chassis, 240D 300D 300TD 300CD 300SD from 1977 to 1984. PLEASE NOTE: WILL NOT FIT MODELS WITH ABS.
Very good used ash tray frame mounting assembly with very minimal corrosion. These are often badly corroded or damaged from abuse. This fits all 123 chassis sedans, coupes and wagons.
Set of right and left front speaker grills ( cover ), original to W123 chassis sedans, coupes, and wagons that have the climate control temperature sensor in the right side speaker cover. These covers are in very good condition. Good non-deteriorated fiber screens on the backside.
Good used set of left and right aluminum rear hatch alignment slide assemblies and shim plates as shown. These fit all 123 TD wagons from 1979-1985. If your rear hatch is sloppy and loose, it may be excessively worn guide plates.
Good used dash light sockets with 3 new bulbs as shown. The sockets are in good working condition. If your sockets are loose in the hole, bent or burnt, this is a good opportunity to replace them with a couple of good used factory original bulb holders.
Fits ALL 201 124 and Late 126 Gasoline models with the 6 cylinder 103 Engine. Here is a brand new oil pan plug with copper washer.
Fits 1968 to 1985 108, 109, 107, 114, 115, 116, and 123 chassis all models.
Good used right-side power mirror switch. Fits in center console shift cover and this fits later model 123 chassis 1982-1985 and Early 126 1981-1985.
Good complete set of star head silver bolts for 617 5 cylinder turbo diesel engines from 1978-1985. These should be replaced with new or good used if your engine has overheated enough to blow a head gasket. A special socket is required. See related products below:
Good used sunroof air dam closing guide rail, complete with good plastic tabs intact on both ends. This fits right or left side and allows the sunroof to close the air dam before it reaches the edge of the roof.
Good used ORIGINAL interior black plastic lock knob, common on most models in the 1970s and 1980s. This has good plastic and good threads. Sold as a single unit, if you need more, just change the quantity at checkout.
Fits ALL 123 240D 300D 300CD 300TD Diesels from 1977-1985, and ALL 116 and 126 300SD Diesel from 1978-1985. Here is a brand new Genuine OEM Alternator mounting bracket with new adjustment nut.
Good used front crank bolt 3 spring washers. Sorry we do not have any bolts.
PLEASE READ CAREFULLY BEFORE ORDERING!
Fits 1979 to 1985 US Model 240TD and 300TD only
f7a5.jpg)
Brand new Genuine OEM turbo diesel kickdown switch. Fits 123 turbos from 1982-1985 and 126 turbos from 1981-1985. This switch is located under your accelerator pedal, and it tells the transmission when to down shift. If the switch breaks it can stick in or on!
This is a brand new Elring seal and gasket installation kit for the 617 Turbo diesel turbo charger. Fits 116 Chassis 300SD from 1978-1980, 123 Chassis 300DT and 300TDT from 1981-1985 and 126 chassis from 1981-1985.
Here is a brand new set of Rear brake hoses for all 123 chassis 1977-1985 and 126 chassis 1981-1991, both gasoline and diesel models and 116 Chassis 300SD only, and 1973 to 1980 450SL. Also fits 380SL from 1981 to 1985 -- US MODELS ONLY
Here is a brand new set of Front brake hoses that fit all 123 chassis from 1981-1985 and 126 chassis from 1981-1991, both gasoline and diesel models.
_______________________________________________________________________________
Brand new Genuine OEM hubcap clips for Chassis 108 114 115 116 107 123. Sold in a set of FIVE.
These will fit the standard 14 inch round hubcap on all chassis listed above.
Brand new Contitech Serpentine belt for 300CE 300SE 300SEL 300TE 190E from 1990-1993 with 104 engine. There are some vin splits on the end year, so any questions EMAIL with vin number before ordering.
SKU:GEG-COMSTB
If you have a stuck key or failed lock in your 1977 to 1979 W123 this is your best option for a reliable replacement but we only have a few of these in stock. The exact originals as shown in the picture below are no longer made. These do not have a replaceable tumbler assembly.
Good used exhaust manifold assembly with no cracks. Fits 1980 and 1981 300D non turbo that uses EGR valve. Please note EGR valve hole. This exhaust manifold can also be used in the 1977 - 1979 models but you would need to plug the EGR access hole in the center of the exhaust manifold.
Applies to 240D 300D 300CD 300TD 300SD Diesel This guide is written specifically for owners of 123 and 126 diesels from 1977 up to 1984. There are some sections that apply to the 115 and 116 chassis but it is not specific to those models.
Set of 10 fuel injector sealing washers. Also know as heat shield crush washers. Fit 1984 to 1999 Mercedes aluminum head 60x. diesel engines 4, 5, and 6 cylinder (190D, 300D, 300TD 300D 2.5 300SDL 350SD S350 and E300D).
Fits all Diesels from 1965 to 1985
New ContiTech Serpentine Belt. PDF Instructions included!
_______________________________________________________________________________
How to view the PDF digital instructions:
New belt tensioner pulley. Common cause of noise at front of engine when bearing starts to go. Should be replaced at 120K as a preventative measure.
This is a great kit for your 350SL, 450SL, 450SLC, 380SLC, 380SL, and 560SL from 1972 to 1989. It also fits all W114 and W115 Sedans and Couple both gas and diesel from 1968 to 1976. Brand new UPPER control arm inner bushing repair kit.
Brand new upper ball joint assembly with hardware. Fits all 114 115 Sedans and Couple both gas and diesel from 1972 to 1976. Also fit early SL and SLC convertibles and coupes - all 450SL, 450SLC, 380SLC, and 380SL from 1972 to 1985. Replacing the upper ball joint is not a do-it-yourself job.
This is a great kit for you 114 and 115 owners. Fits all Sedans and Couple both gas and diesel from 1968 to 1976. Also fit early SL and SLC convertibles and coupes - all 450SL, 450SLC, 380SLC, and 380SL from 1972 to 1985. Brand new set of 2 lower ball joints. This is not a do-it-yourself job.
This is a great kit for you early SL and SLC owners. Fits all 450SL, 450SLC, 380SLC, and 380SL from 1972 to 1985. If you are getting a lot of body roll in the turns this kit will really tighten up the front sway bar.
This is a great kit for you 114 and 115 owners. Fits all Sedans and Couple both gas and diesel from 1968 to 1976. If you are getting a lot of body roll in the turns this kit will really tighten up the front sway bar.
Set of four (4) new factory door striker bolts. It is very easy to round these off. If you are planning on removing or adjusting your strikers and want the original style hex bolts you should have extras on hand.