Search | On Demand Video

If you are planning to remove your 722.9 conductor plate for inspection or repair, you will want to take the time to thoroughly clean the plate, the valve body, and the solenoids. No cleaning agents or foreign chemicals should be used.

This video applies to both K-jetronic and KE-jetronic fuel injection engines on Mercedes from 1976 to 1993.. Let's say you just acquired an old gas engined  Mercedes and you just can not get it to run right and or even get it to start.

This is absolutely the best thing you can do for your older 2003 to mid-2010 Mercedes 7-speed transmission. In this 19-minute video, Kent will show you what is required to purchase and install to make this upgrade on an early 722.9 transmission. Yes, it is something you can do yourself!

In this 10-minute installation tip video, Kent will show you a few things you need to be careful about when either installing new coil packs or ignition wires in your 1998 to 2006 V8 or V6 engine.

In this long 32-minute instructional video, Kent will demonstrate removing a failed water pump and replacing it will a new one on a W211 E500 with the M113 engine.

This can be a frustrating job if you do not know how the fasteners work or the correct sequence when replacing the sensor. In this 15-minute video, Kent will walk you through the R and R procedure step-by-step and will use the camera to show close-ups on how everything goes back together.

If you are working on engine valve cover oil leaks, plan to replace these hoses unless they have been recently (last five years) changed. More often than not, they can not be reused.

This is a 5-minute instructional video to show you how to attach an inline magnetic filter to your power steering system. Great protection and easy to do. You will lose some fluid unless you pinch off the hoses before cutting out a section to install the filter.

In this 7.5-minute video, Kent will share some tips on getting to the bolts and nuts, removing the old ABC pump, and fitting in a standard M113 power steering pump.

In this 6+ minute video, Kent will demonstrate how to locate and cut out 3-inch (approx.) holes in your trunk carpet to allow you to remove the bolts and the wire attached to the top of your ABC strut. Then you can replace it or install coil-over shocks in their place.

In this 6-minute instructional video Kent will show you how fully bleed the air out of the power steering system on an M112 or M113 engine so you can get rid of that annoying squeal when you turn the wheel. This happens after doing a flush or replacing a power steering pump.

In this 13-minute CIS training video, Kent will walk you through the steps recommended by Mercedes Benz to fully test the operation of the EHA valve on 1984 to 1993 4, 6, and 8-cylinder engines with KE-jetronic fuel injection.

After completing the pressure test on your CIS engine, you discover a problem. But how can you find out how to isolate and fix it? This is going to require some research on your part. Start by learning how the system works and how each component plays a part.

This video is specific to K- jetronic fuel-injected engines from 1976 to 1985. This includes the 350, 450, and 280 engines in the R107, W116, W123, and early W126 gas Mercedes. In this 29-minute video. Kent will show you how to hook up the gauge, run the fuel pumps, and complete the test.

To do proper system testing on CIS fuel injection, you must find a way to get the fuel pump or fuel pumps to run continuously without the engine running. This can not be done by just using the ignition key. In this 15-minute training video, Kent will show the options available to do this.

People call these two units pressure regulators, but really only one of them is. In this xx minute video, Kent will explain how these are different, what each one does, how to adjust them, and how to test them with a hand pump vacuum tester. 

In this xx minute instructional video Kent will walk you through the process of hooking up the gauge, taking the proper readings at idle and at rpm, adjusting the regulator, checking for internal leaks, and depressurizing before removal. 

In this 30 minute instructional video Kent will use a 1972 300SEL 4.5 to show you how to remove the master cylinder with minimal spillage, how to install the tank and bench bleed a new master cylinder, and how to reinstall it with minimal brake fluid spillage while protecting your car's paint. 

In this 14 minute instructional video Kent will demonstrate how to remove and install a new thermostat in a 450 engine. Here you will see how tight it is to get install in a 300SEL 4.5, but other V8s will have better access.

In this 33-minute instructional video, Kent will show you how to convert your old points ignition to an efficient modern electronic ignition. Rid yourself of those old high-maintenance distributor points forever.

Also covers 1980 W116 sedans. In this 18-minute instructional video, Kent will wrap up his 5-part series on fixing and servicing these old sunroofs. You will get to see just how well it works after proper repair, lubrication and adjustment. These are the subjects that are covered.

In this 23 minute highly detailed video Kent will show you to reasons why and some of the problems you will run into when you change these hoses on your own D-Jet engine. He will take the new parts and show you how to properly install them using the correct hose clamps, sealants and lubes. 

Also covers 1980 W116 sedans.

In this 36-minute instructional video, Kent will walk you through the process of doing a complete fuel hose replacement and fuel injector service on a 1970 to 1975 Mercedes V8 engine with Bosch EFI electronic fuel injection.