ALERT: Miracle Paint is back in stock! CLICK HERE to order.
This tool is required to remove the prechambers in the OM 615, OM 616, OM 617, OM 601, OM 603 four, five, and six clyinder diesels through 1987 ONLY! Easy tool to use.
For all 108, 109, 114, 115, 116, 123, and 126 (up to 1985) with video instructions
6 "German style" non-cutting hose clamps as shown. These are wider than most to better seal the hose to the fitting. See our other hose clamp assortments below.
Learn how to install this critical repair kit correctly and how to test your monovalve function on the bench. In this 13-minute video, Kent shares how to install the kit while avoiding problems. Get your cabin heat working properly again!
This fits the U.S. models with automatic climate control which include the 1982 to 1989 R107 380SL, 500SL, and 560SL + the 1982 to 1985 W123 ALL models + the 1981 to 1991 W126 sedan and coupes. This is an easy fix that you can do yourself.
In this 24-minute instructional video, Kent shows you more than just how to change the transmission filter and the pan.
In this 19-minute detail instructions, Kent will show you how to get the old seal out, how to trial fit the new seal, and how to glue it in place properly. You can not believe how many seals we see that have not been installed properly.
In this detailed 22-minute video instruction, Kent will show you how to use his kit to perform a power drain on most 1965 to 1995 automatic transmission.
Yes, YOU can fully drain all your transmission without using any type of "power flush." Full detailed video instructions are included. This kit is easy to connect and the process is quick and clean. Watch Kent's YouTube video below for full details.
For the past 20+ years, we have promoted H4 headlight upgrades for these old Mercedes. The original sealed beam headlight bulbs lacked light output, and we found them sometimes downright "sketchy" on dark roads, especially when deer were known to be present.
You will receive ten each of the following sizes: 8/12, 10/16, and 12/22. These are much better than U.S. style hose clamps that cut into the hose.
Kent shares with you 3 key steps that you should consider doing to get your old fuel injected 6 and 8 cylinder engines running properly. These include:
These require removal of the batter and possibly the brake booster to replace. They are split so you do not need to remove the sway bar. Plan to replace if doing work under the battery box area. Battery acid is hard on the right side.
These will no longer be printed when these are gone. They will still be available as a download. All books are signed by Kent. This is an end of an era for us. Most books are approximately 15 pages in length and covered with heavy clear plastic.
This kit has enough red clips (60) to do both sides on the 123 240D, 300D, 300TD, 300CD, 280E, and 280CE. You will receive the best tool to remove the side trim and the best tool to remove the old red clips from the side trim after removal.
You can not believe how easy it is to move and adjust your old seat after lubrication the tracks with this amazing lubricant! You will receive two full tubes plus the extension nozzle. This is more than enough lube to do the seats with four tracks on each side.
These quality 6.5 inch wire cutters are made of special steel, the blades are high-frequency hardened steel. Suitable for cutting soft copper wire, plastic wire, small cable, aluminum wire, soft alloy wire, jewelry making, multifunctional manual edge banding pliers.
ONLY one available. These are the actual parts you will receive packed carefully.
In this 15-minute video, Kent will show you step-by-step how to safely remove the Bowden cable without damaging it and how to install it to get the proper connection. This is not as easy as it looks, and you can break it if you are not careful.
In this 9-minute instructional video, Kent explains how to set up his injection pump cleaning and testing kit ( available separately ), and use it to clean out old fuel injection pumps of gum and grime, and then how to test them to make sure they are delivery fuel through every line.
This is the best way to determine if the expensive injection pump is going to work for old 4 AND 5-cylinder diesel engines that have not run in years. Watch the video below to understand what this kit can do.
We know you will be very happy with the quality of these plastic headlight surrounds!
In this 20-minute instruction video, Kent will show you how to take his short kit and combine it with a tester that you can purchase online to make a leak-free, reliable, and accurate fuel pressure tester for Bosch CIS fuel injection.
It has been over 30 years since the last Mercedes with Bosch C.I.S. fuel injection was manufactured. If you own a 1976 to 1993 Mercedes gas engine with this type of fuel injection, you may have difficulty finding someone to work on your car. In some parts of the country, it may be impossible.
New LEFT side rear door seal for sedans only. Excellent quality aftermarket part with a good fit. If you need instructions, please look below to see the special tools that come with them.
Flushes Out Old Grease and Repacks Bearings with Less Mess. This Handy Packer works on bearings up to 3 1/2" O.D.
Excellent quality zinc plated hose clamps as shown. These can be tighten with a straight blade screw driver or a 7mm socket or nut driver.
Kent is a firm believer in using these strong magnets inside a transmission pan to help extend its useful life.
They should be placed toward the rear of the pan as shown in the picture below.
This is an excellent replacement if yours has melted and deformed.
If you own, plan to own, and want to enjoy driving your old CIS fuel-injected Mercedes, Kent highly recommends you learn to do a full fuel system flow and pressure test.
One very minor weakness on the W123 is the glove box door. This is because 2 of the key stress points built into the door are made of plastic. One would be the pin holding the latching mechanism ( Kent already has a repair kit for that - see related products.
Even many old-time Mercedes diesel "experts" are surprised about this part. It is so unknown that it never gets replaced in the oil filter housing, meaning that almost all of them are no longer working today. Watch the video below, and Kent will explain its location and function.
Many of these, especially along the bottom of the hard are hard and brittle and will break when removing the panel. Tilt and twist to remove and install in the holde. Sold in a bag of 24.
In this 17-minute video instruction, Kent walks you through the steps to install his door liner kit using thick, clear, and high-quality plastic sheets on both front and rear doors. A W123 sedan is shown here, but the principles are similar for other chassis.
If you own an older Mercedes sedan or wagon, it is a very good idea to remove all four door panels, repair components, clean drains, and, most importantly, lubricate all moving parts, as Kent explains in numerous YouTube videos.
SAVE BIG! These critical front suspension parts will restore the factory road feel on your old 123. Watch the video as Kent will explain what they are, where they do, and what is involved in replacing them.
This kit contains the following new parts:
This is the actual panel you will receive. Notice the empty cutout for the A/C temperature control wheel.
Reads English on one side and German on the other.
These transmission pans get "out of shape" due to over-torquing the bolts. That crushes the stops (see below), and when that happens, it is very hard to get the pan seal not to leak. Your best option if you are doing a transmission service is to replace the pan.
When pressure testing your KE-jetronic fuel injection, you may find you need a really thin wrench to install the small fitting on the right side bottom of the fuel distributor.
Also works on 380SL and 560SL transmissions. Before you think you can easily remove the Bowden cable from the transmission, watch the video below.
These transmissions are now 40+ years old, and with age comes hardened o-rings and seals, leading to what I call "pesky" leaks. They are not bad enough to flow on the ground, but they do leave wetness around the transmission and drips on the garage floor.
These transmissions are now 40+ years old, and with age comes hardened o-rings and seals, leading to what I call "pesky" leaks.
New left AND right side upper control arms. They will fit ALL W116 chassis from 1973 to 1980 ( except 6.9 ), and ALL W123 chassis sedans, coupes and wagons from 1977 to 1985.
You must drive this star bit into the head of the damaged bolt with a hammer, but it will hold. The bolt will then need to be replaced. Watch the video below as Kent will explain how it works.
For mount kits and hardware, see related products below.
This will replace the plate with cracked or striped out threads on your oil pressure line. Gasket available separately below.
30 light bulbs total in this assortment. PLEASE NOTE: These may not be every bulb you will need for every model, but you will have extras on hand. These cars are OLD, and most of the bulbs need to be replaced. They even start to loose some of their intensity over time.
This is a complete kit. Aftermarket new plastic breather tube with rubber attachment elbows, one new clamp, and a zip tie. You can see below how it installs on a turbo 300TD wagon. Watch the video for more specific details.
High quality fast break in pads with special coated anti-squeal pad bonded to the back side of the pad. We include 4 new sensor wires and a small ceramic brake pad grease to lube the pad edges and the pins. ( no need to lube the back side).