ALERT: Miracle Paint is back in stock! CLICK HERE to order.
This is a genuine Mercedes used part. These are much stronger than the aftermarket ones available. Genuine are no longer made. No damage to the slot or the threads. Only for models listed. Does not work on later aluminum diesel engines. Collar nut holds pre-chamber in cylinder head.
These two small o-rings seal the oil drain tube that goes from the bottom of the air filter into the engine oil pan.
8/2022 Update: We have modifed a new wrench for this kit so it may not look the same as that shown in previous YouTube videos, but it will do the same or even better job! We do sell the water pumps individually, but we decided to offer this complete kit to make a diesel pump installation go easie
PLEASE NOTE: We have been having problems recently obtaining these brackets. Turbo owner you may want to get a backup now before these are gone forever. If you order there could be a short shipping delay. Complete Kit as shown with installation tips included.
Good used turbo charger center section heat shield plate as shown. This only fits the Garret T3 Turbo. Will not fit the KKK turbos. Will not fit 1985 models with trap oxidizer.
Good used turbo charger center section to turbine housing hold down ring plate as shown. This only fits the Garret T3 Turbo. Will not fit the KKK turbos. Will not fit 1985 models with trap oxidizer.
Good used turbo charger exhaust manifold with good studs as shown. No other parts included. This only fits the Garret T3 Turbo. Will not fit the KKK turbos. Will not fit 1985 models with trap oxidizer. This is the style that has the EGR outlet.
Good used turbo charger compressor housing as shown. This only fits the Garret T3 Turbo. Will not fit the KKK turbos. Will not fit 1985 models with trap oxidizer.
These large o-rings are used on the aluminum coupling that connects the turbo charger compressor outlet to the intake manifold. Should be changed with removing manifold or replacing turbo.
With this kit you will be able to hook up a pressure gauge to your intake manifold and route it inside your car for the purpose of monitoring your turbo charger boost pressure while driving.
When using a pencil glow plug reamer, this modified 12 mm wrench will allow you to PUSH in on the reamer while turning - and let me tell you - this is needed when you have heavy carbon buildup in the prechambers.
Three seals required to repair oil leaks in the straight oil drain tube going from the bottom of the turbo into the engine oil pan. This kit is intended for those who are rebuilding their turbo and have not changed these seals before.
High quality lubricant to be used when assembling bearings in engines or in components that are oiled by engine oil. This WILL prevent scoring and wear upon initial start-up after overhaul.
This is the actual bracket and shocks you will receive. Shocks are stiff with no internal looseness. Top rubbers are usable. Both rubbers and hardware are missing.
Good used engine shock as shown. Fits right or left side.
Lower Engine Gasket and Seal Set as Shown. Contains many sizes of aluminum sealing washers. Please study picture carefully to see exactly what you are getting.
This sealing ring provides seal at the connection of the flexible down pipe and the exhaust pipe going back to the center muffler. This is an upgrade replacement for the older style crushable gasket seal. This all metal ring provides a much more reliable seal over time.
These are the plastic bushings that hold fuel injectors into the head of the late M116 and M117 engines. These get very brittle with age. If you are planning on removing your fuel injectors I highly recommend you order these to have on hand.
This is a critical rubber part that seals the fuel injector to the injector holder. Deterioration can result in high idle speeds and poor engine performance. Unless you have a low mileage car with soft seals, these should be changed when testing, cleaning, or replacing your fuel injectors.
This rubber mount is often torn up, oil soaked or just plain missing. It sits right behind the center of the oil pan on a number of models listed above. I have often see the entire assembly removed. Check first to see if your engine has one before ordering.
Here are the correct size metric nuts with built in shoulder washer. If you drop these in behind the injection pump you may never find them. When doing glow plug service it is always a good idea to have some spare nuts on hand. New Bosch glow plugs do not come with new nuts.
This o-ring has to be tough enough to handle the high heat at the injection pump. If you see oil leaks around the area of the rack damper (located on bottom at rear of injection pump) then replace this o-ring.
Application: Applies to the model listed above. Excellent quality. They are Bosch Duraterm brand glow plugs.
New nylon fan replacement. Only install on a fan clutch that originally had a nylon fan ( not an aluminum one). Shows up primarily on 1984 and 1985 models.
WILL NOT FIT 85 CALIFORNIA MODELS!! It will fit some 1985 Federal Models only.
This is a very common failure item on the older gas models. The braided outlet fuel hose will rot and and begin by weeping fuel through the hose. When it finally fails it can be dangerous and leave you stranded on the road. Large amounts of fuel will come pouring out of the tank.
This check valve is mounted on the end of the electric fuel pump and prevents pressure from bleeding off after the engine has shut down. If you engine is slow to start after it has sat overnight that could be a sign the check valve needs replacement.
This will only fit Garrett T3 turbos. If you order in error it is not returnable. The picture below shows where it is located. You will ONLY receive the flex part that is clamped as shown.
This kit is for replacing the bushings associated with the engine shock. Sold Individually.
These washers are installed right under the four nuts that hold the valve cover securely to the cylinder head. They help to prevent the over tightening of the valve cover as well as prevent the nut from loosening up. They also keep the nut from gouging the metal out of the valve cover.
This is a common oil leak area on the 300SD. The gasket fits between the oil filter housing and the plate that mounts the oil pressure sending unit. This is a genuine OE gasket.
New timing chain tensioner and gasket.
Set of good, used original pan bolts with washers. Common places for these bolts to round out. Keep in mind these are the SHORT bolts. There are other bolts that are used on these pans that are longer.
Applies to all 200D 220D 240D 300D 300CD 300TD 300SD 1965 to 1985
Another High Quality product from Lubro Moly. This is a 300ml can of Motor Oil Saver. It Rejuvenates rubber and plastic engine seals and reduces oil consumption via the piston rings and valve guides; counteracts the loss in viscosity of motor oils.
Make certain your pump only has one main line coming into it. Very good cover plate as shown. No cracks or wear. No other parts included. To be used if your cover plate gets damaged. Sorry no complete used pumps available.
USED
Brand new thermostat, heavy-duty short hose, and 2 new clamps. Fits all 126 Chassis 380 engines from 1981 to 1985 both in 107 chassis and 126 Chassis. Free Video installation tips included ( click on the arrow in the center of the picture to watch below:
This item can only be shipped UPS Ground because it is a liquid. One Liter of correct Power steering fluid. Fully compatible with Dexron II systems but has enhanced aditives to reduce steering box gear wear.
Fits 124, 126 and 201 chassis - 124 Chassis 300E 2.6, 260E, 300E, 1986-1992, 1988-1989 300CE, 126 Chassis 300SE, 300SEL, 1988-1991, 201 Chassis 190E 2.6, 1987-1993.
Brand new Bosch Distributor rotor for above models.
Brand new Bosch Distributor Cap for 103 Engines from 1986 to 1992.
Each fuel pump has a critical check valve mounted at the pump outlet. The purpose of this check valve is to prevent fuel from leaking back through the pump after the engine has been shut down. Constant fuel pressure must be held in the fuel system for the engine to restart quickly.
Application:
Brand New Engine block gasket set for 4 cylinder 240D.
.Please review picture. What you see is what you get. 3 different lengths.
The fuel accumulator maintains the pressure in the fuel system for a certain time after the engine has been switched off. When the engine is running it serves to deaden the noise of the electric fuel pump.
Brand New short banjo bolt. Fits on top of injection pump on 617 Turbo Diesel ALDA and on 4 and 5 cylinder diesel water pump bypass pipes (often broken or rusty). This includes 220D 240D 300D 300TD 300CD and 300SD.
New aluminum washers (2) for long banjo bolt at rear of intake manifold and also for short banjo bolt at connection to ALDA on top of injection pump. These banjo bolts MUST not leak. These aluminum washers are often missing or damaged. Two washers required for each banjo bolt.
For use with the following modesl below. Check size if unsure.
New rubber stop for rear exhaust bracket. It plugs into the body right above the back of the rear muffler. Helps prevent rattle. Fits almost all models from late 1960s to mid 1990s. When you hear something clunking in the back when you go over a bump, this part is probably missing.
Brand new factory type braided cloth injector end plug for all diesels 220D 240D 300D 300CD 300TD 300SD 300SDL E300D, from 1968 to 1995. Sold individually. Check yours for cracks or leaking! Very important that the end plug be in good condition or fuel leaks will occur.