ALERT: Miracle Paint is back in stock! CLICK HERE to order.
Kent walks you through replacing a trunk seal on a 1970 280SL. The video is 13 minutes long and covers removing the old seal, cleaning the groove, trial fitting the new seal, and the final gluing procedure.
In this detailed 22-minute video instruction, Kent will show you how to use his kit to perform a power drain on most 1965 to 1995 automatic transmission.
Yes, YOU can fully drain all your transmission without using any type of "power flush." Full detailed video instructions are included. This kit is easy to connect and the process is quick and clean. Watch Kent's YouTube video below for full details.
You will receive ten each of the following sizes: 8/12, 10/16, and 12/22. These are much better than U.S. style hose clamps that cut into the hose.
You can not believe how easy it is to move and adjust your old seat after lubrication the tracks with this amazing lubricant! You will receive two full tubes plus the extension nozzle. This is more than enough lube to do the seats with four tracks on each side.
These quality 6.5 inch wire cutters are made of special steel, the blades are high-frequency hardened steel. Suitable for cutting soft copper wire, plastic wire, small cable, aluminum wire, soft alloy wire, jewelry making, multifunctional manual edge banding pliers.
I am throwing in the wires for free, so please, no complaints. They work and are not all the same color, but you could use them if you ever need to replace one wire. The two wire holders for the valve covers are also included from free.
Excellent used all-metal driver and passenger-side tail light bulb holders for early sedans. The later models were plastic. These are exceptionally nice units with very bright reflectors and clean bulb sockets.
In this 9-minute instructional video, Kent explains how to set up his injection pump cleaning and testing kit ( available separately ), and use it to clean out old fuel injection pumps of gum and grime, and then how to test them to make sure they are delivery fuel through every line.
Watch the video below to understand what this kit can do. Ensure your injection pump is thoroughly cleaned and lubricated before starting the engine after long storage.
This fits a number of lmid 1960s to early 1970s models with automatic transmission. 250SL 280SL 250S 250SE 280S 280SE 280SE 300SEL. Check under the front of your car to make sure this matches what you have before ordering.
Just so you know, not all parts shown will fit in all years and models of the W108 and W109. There may even be some “stray parts” here that belong to other chassis. These are parts that Kent has collected over the past 25 years.
Flushes Out Old Grease and Repacks Bearings with Less Mess. This Handy Packer works on bearings up to 3 1/2" O.D.
Excellent quality zinc plated hose clamps as shown. These can be tighten with a straight blade screw driver or a 7mm socket or nut driver.
Kent is a firm believer in using these strong magnets inside a transmission pan to help extend its useful life.
They should be placed toward the rear of the pan as shown in the picture below.
Many of these, especially along the bottom of the hard are hard and brittle and will break when removing the panel. Tilt and twist to remove and install in the holde. Sold in a bag of 24.
Almost every early SL Kent comes across needs new front wheel bearings. These get so neglected and hardly ever replaced. We are offering a very high quality kit as shown above that will include free grease for your new wheel bearings.
Watch the video below to understand what this kit can do. Kent used it on his 6.3, which had sat outside and had not run in 18 years. The 6.3 injection pump is rare, to say the least, and can be very expensive to overhaul. Treat it with great care!
In this 17-minute video instruction, Kent walks you through the steps to install his door liner kit using thick, clear, and high-quality plastic sheets on both front and rear doors. A W123 sedan is shown here, but the principles are similar for other chassis.
If you own an older Mercedes sedan or wagon, it is a very good idea to remove all four door panels, repair components, clean drains, and, most importantly, lubricate all moving parts, as Kent explains in numerous YouTube videos.
These plugs will NOT work on your original injectors. They will ONLY work on our new replacements (see below). These plugs are a good alternative to the damaged originals on your D-Jetronic fuel-injected engine only if you are installing our new injectors.
New tensioner as shown. No specific instructions are available but this can be installed from outside the engine once you get access the the hold down bolts.
Nice to have a few extra 13mm sockets around. This is the first tool that gets lost when working on old Mercedes. The tall shoulder inside helps to hold the nut or bolt in a position to make it easier to start the threads.
ONLY ONE SET AVAILABLE. Three of these wrenches are made by Gearwrench. You get a very long standard combination 13mm wrench, a long 10mm with a racheting box, a very long 17mm with a ratcheting box, and finally, a very long 14mm combination wrench made by Urrea.
If your front seat fore and aft adjustment handle is cracked or broken, we have the right replacement upgrade for you, which is stronger and more comfortable to pull on. This is a beginner DIY job on most seats. You cut and chisel the old handle off and bolt on this new handle.
These are the critical seals that go on the D-jetronic fuel injectors. If they leak air, your engine with idle high, start poorly and run lean, which can damage the pistons. We recommend you replace these whenever you remove and replace the injectors.
Best upgrade for 1958 to 1972 6 cylinder 220SE, 220S, 230, 250S, 280S, 250SE, 280SE, 280SEL, 230SL, 250SL, 280SL and 4 cylinder gas 190,
WARNING: MAKE CERTAIN your current injectors are yellow at the top. A restocking fee will apply if you place an order in error. For the 3.5 engine ONLY. See related products below if you have a 4.5.
Let's face it. These fuel tanks and now 50 years old and most are not squeaky clean inside. There is a fuel tank screen that will catch most particles if the screen is in good shape. But I have found that it will not catch the very fine rust particulates that are so common in these old cars.
Best upgrade ever for your 180, 190, 200, or 220 gas engine. Even included the 190SL.
People call these two units pressure regulators, but really only one of them is. In this xx minute video, Kent will explain how these are different, what each one does, how to adjust them, and how to test them with a hand pump vacuum tester.
In this 8-minute video, Kent will show you how to quickly depressurize your D-Jetronic fuel system before doing any injector service, replacing any hoses, or hooking up our fuel pressure tester.
In this xx minute instructional video Kent will walk you through the process of hooking up the gauge, taking the proper readings at idle and at rpm, adjusting the regulator, checking for internal leaks, and depressurizing before removal.
This kit will put a smile on your face, especially if you have done it before the "old way." Watch the video below for full instructions on how to use this kit to do the fastest fuel system depressurization in the world!
This procedure is a must do anytime you install a new master cylinder or allow fluid to completely leak out of your master cylinder.
In this 30 minute instructional video Kent will use a 1972 300SEL 4.5 to show you how to remove the master cylinder with minimal spillage, how to install the tank and bench bleed a new master cylinder, and how to reinstall it with minimal brake fluid spillage while protecting your car's paint.
These will also fit the 1972 U.S. version 350SL with the 4.5 engine. Just make sure of the correct color. WARNING: MAKE CERTAIN your current injectors are blue/green at the top. A restocking fee will apply if you place an order in error. These are for the 4.5 engine only.
Here is a 15 minute video that can really help you if you have small coolant leaks around your idle air valve. You will learn how easy it is to break the bolts when removing this valve, and your option to fix it.
In this 14 minute instructional video Kent will demonstrate how to remove and install a new thermostat in a 450 engine. Here you will see how tight it is to get install in a 300SEL 4.5, but other V8s will have better access.
In this 12 minute instructional video, Kent will demonstrate how to remove and replace the viscous fan clutch in a 1972 300SEL 4.5. Other topics covered will be cleaning and corrosion prevention. This video is included free with the purchase of our fan clutch install kit ( see below).
Also covers the 1980 W116 sedans.
In this 33-minute instructional video, Kent will show you how to convert your old points ignition to an efficient modern electronic ignition. Rid yourself of those old high-maintenance distributor points forever.
In this 29-minute instructional video, Kent will show you how to convert your old points ignition to an efficient modern electronic ignition. Rid yourself of those old high-maintenance distributor points forever.
WARNING - WARNING - WARNING: BEFORE we ship this unit, we MUST have confirmation from you that you have removed the distributor cap, confirmed the size of your rotor ( see below), AND measured the points cam width and height. If your distributor is not exactly the same this kit WILL NOT WORK.
Most of the older 450 engine fan clutches are still original on most of the older unrestored V8 models from 1970 to 1980. If you are having problems with your 450 V8 running hot check the friction in your clutch. They are often worn out as they seem to never get changed.
This is seldom replaced. If you engine is taking over 15 minutes to get up to full operating temp then your thermostat is probably worn now. We got you covered with kit. We will get you the extra hardware, supplies and video instructions so you have the confidence to do this job yourself.
Also covers 1980 W116 sedans. In this 20-minute instructional video, Kent will walk you through the steps of getting the steel sunroof panel installed properly back into the car's roof. The first step will require cleaning, inspection, and possible replacement of the plastic slides.
In this 23 minute highly detailed video Kent will show you to reasons why and some of the problems you will run into when you change these hoses on your own D-Jet engine. He will take the new parts and show you how to properly install them using the correct hose clamps, sealants and lubes.