Search | W124

Displaying 351 - 400 of 514
$46.00

1990 to 1995 60x OM(602 and OM603) Diesel Prechamber Removal Special Fitting for Slide Hammer

Slide hammer not included. Can be purchased below with a slide hammer if you don't already have one.

 This is a special pre-chamber threaded fitting that you can attach to YOUR slide hammer  to remove the pre chamber on 1990 to 1991 350SD 350SDL (126 chassis), 1990 to 1993 300D 2.5 (124 chassis), and 1992 to 1995 300SD / S350 (140 chassis).  You will need to own or purchase a 5 lb slide hammer a

$16.50

190E 190D 260E 300E Transmission Pan Gasket Only

Also fits CAL. 1985 Models 300D 300CD 300TD and 300SD with 722.416 transmissions

Brand new gasket. Make sure this fits your transmission before ordering. No returnable if ordered in error.

$39.60

High Visibility Easy Adjust Click-Stop 3/8 Inch Drive Torque Wrench and Case

Perfect size for torquing spark plugs and other under 50 ft. lbs. important engine components.

This is a huge improvement over the older torque wrenches that I have seen around for years. I know it is a little more expensive, but after you use it, you will agree it is well worth the money. It is perfect for spark plugs and mid-size fasteners around the engine.

$3.99

Maintenance-Handy Pick Tool Set

Small enough to get into tight places - i.e. brake clips and heat shields

Nice set of pick tools with plastic handles. They have strong steel tips which allow for more prying and twisting with less tendency to bend the tips as you would with dental pick tools. Note: Quarter is not included! Shown for size reference only

$31.80

Engine Crank Rotation Adjustable Length 1/2 Inch Drive Ratchet Wrench

Rotate Engines on 220D 240D 300D 300CD 300TD 300SD 300SDL and all V8's from 1970 to 1991 - Extends to 18 inches long!

This is Kents new favorite ratchet wrench for turning engines over during service and repair. There are a number of maintenance procedures that require you rotate the engine over by hand.

$16.75

Axle Shaft Seal

Final drive seal (45 x 65 x 11mm)

Fits Mercedes Benz:

$2.75

Service 10 mm Head Size Locking Nuts ( Set of 10 )

Common size on all Mercedes

Replace those nuts that keep loosening up with nylock metric nuts that just won't come off. Inside the door panel on the window regulators. Around the engine compartment. Air filter housing nuts. etc. etc.

$45.80

Early Diesel Pre Chamber Removal Threaded Tool (up through 1987 models only)

A slide hammer is required. A collar nut tool is required. See the full explanation below

If you already have or are willing to buy a 5 pound slide hammer this special threaded fitting will allow you to PULL the pre-chamber from the cylinder head once you have removed the collar nut and the glow plug ( a collar nut removal tool is required look below to learn more).

$19.95

60x Injection Pump Stop Lever Shaft Leak Fix Repair KIT

For 5 and 6 cylinder diesels 1986 to 1995

This is one of the more common oil leaks I see on the 602 (5 cylinder) and 603 (6 cylinder) diesel engines. In fact, I have seen it on almost every one of these engines I have worked on.

$22.75

Fluid Maintenance - Radiator and Fuel Hose HD Pinch off Pliers

A must when changing rear mount fuel filters and pumps. Best tool for secure clamp-off in tight locations. Works on fuel hose, coolant hose and even big radiator hose.

I have used a lot of different clamping tools over the years to prevent fluids from leaking out when removing coolant, fuel, or brake fluid hoses. Most work ok. Some are hard to use in tight places.  Many do not stop every last drip from coming out of the hose.

$12.80

Genuine Trunk Emblem Grommet - Set of 4

Holds emblems to trunk on many models 1974 to 1985

Grommets push into the holes in the trunk to hold the emblems for the right and left side as applicable. A must have if you plan to repaint your car. Video on how to remove your emblems without damaging them is included free. These will work on the following models.

Mercedes-Benz 230

$6.95

O-ring Removal Fine Point Pick Tool Set

Best set Kent has found to remove orings in hard to get to locations

This set of 5 pick tools have very thin and sharp points. Best set Kent has found to remove orings in hard to get to locations. The variety of angles available allows you to get into almost anywhere to remove and o-ring, sealing ring or other small part.

Sale
$19.00

1/2 Inch Drive Clicker Torque Wrench 20 - 150 Ft. Lbs.

CLEARANCE ONLY 2 LEFT. diesel fuel injectors and wheel bolts!!!

If you are going to work on your diesel fuel injectors, you are going to need a torque wrench. If you are going to tighten your alloy wheel lug bolts properly, you should use a torque wrench. In fact, if you do your own work, you should have a 1/2-inch clicker torque wrench in your toolbox.

$23.95

Diesel Injector Removal Socket and Pick with Instructions

Finally we can offer a strong and very deep socket that will work on all Bosch Diesel Injectors from the late 1950's to 1994

Works on 110, 115, 116, 123, 201, 126 and 124 diesel engines 200D 220D 240D 300D 300CD 300TD 300SD 190D 300SDL. We have found that over half of the deep sockets we test will not go over some of the longer injectors.

$149.95

6 cylinder 603 engine Auxiliary Fan

Fits 1987 300D and 300TD / 1986 and 1987 300SDL --- Also fits 1985 YEAR 300SD ONLY

Brand new Meyle Auxiliary fan motor for 6 cylinder diesel engines from 1986 and 1987.

$34.00

6 Cylinder 603 Diesel Fuel Injector Nozzle (1)

German made for us by Wolfswerke-sachsen ( same company and same nozzle that was formerly branded as Monark)

Fits 300SDL 300D 300TD 300SD 350SDL S350D 1986 to 1993

PLEASE NOTE THE FOLLOWING:

$14.95

Engine Coolant Temperature Sensor

SINGLE pin - located on left side of cylinder head by glow plugs on 1977 to 1985 OM616 and OM617 Diesel engines.

New coolant temperature sensor for most Mercedes built from 1973 to 1993, Gasoline and Diesel models. Many gas models it is located on top of the thermostat housing. Sends signal to engine coolant temperature gauge on the dashboard. These are getting harder to get. Single pin

$22.75

60x Diesel Engine Compartment Fuel Hose and Clamp Replacement Kit

For 190D 1984 to 1993 and 300D 300TD 300SDL 350SD 350SDL 1986 to 1993

This inexpensive kit will allow you to replace the old hardened and brittle fuel hose in your 601 602 or 603 diesel's engine compartment as well as those old worn out factory clamps with new high quality worn gear clamps that will not cut into the rubber hose.

$119.00

603 6 cylinder Head gasket Set

1986 to 1987 300D 300TD 300SDL

Brand new Head gasket set for 6 cylinder diesel engines from 1986 to 1987. Does not include valve cover or valve stem seals.

$8.50
Currently out of stock.

Metal to Metal Anaerobic Gasket Maker

Small .20 Fl Oz for small repairs

This is the absolute best gasket maker when you have a clean and tight metal to metal contact. Examples of where you would use this is SEALING the rear differential cover, aluminum oil pan where is mounts to the engine block, etc.

$29.95

602 603 Diesel Engine Coolant Thermostat w/ INSTRUCTIONS

Fits models listed below with these engines ONLY from 1986 to 1995

New Behr thermostat 80 degree C with gasket. Comes with illustrated installation tips. Instructions are specific for early 603 engine 1986 and 1987 but will apply to other models as well (some specific details may not apply to the later models).

Fits the following models:

$14.95

603 6 Cylinder Diesel Valve Cover Gasket

All 126 124 and 140 chassis with 603 engine. See models below

New valve cover gasket for applicable models listed below with 603 engine.

  • Mercedes-Benz 300D
  • Mercedes-Benz 300SD
  • Mercedes-Benz 300SDL
  • Mercedes-Benz 300TD
  • Mercedes-Benz 350SD
  • Mercedes-Benz 350SDL
$4.65

SVO WVO Copper Coil 1/4 inch Connecting Swedge Fittings (x2)

To go from 1/4 inch diameter pipe to female 1/4 inch NPT thread

Use this special swedge fittings when making any type of copper coil coolant heater for our SVO WVO fuel system. One end of this fitting clamps down tight on the copper pipe and the other end can accept any standard fitting with 1/4 inch male national pipe thread.

$12.95

Maintenance - 10 Inch CURVEDLocking Clamp Plier - Injector Return Hose Tool

Lets you reach into tight places - very long nose curved pliers with teeth - like hemostat

This is one of Kent's favorite tools. Lets you reach into tight places - very long nose curved pliers with teeth - like hemostat. With the locking handles it is amazing what this clamp / pliers can hold - and the tight places it can get into!

$24.95

Late 126 and 201 124 Chassis Auto Transmission Mount

Fits above chassis models listed below from 1986 to 1995 except 300D 2.5

Bad rear mount can cause excessive engine vibration. No instructions included at this time.

Fits 190D, 190E, 260E, 300CE, 300D, 300E, 300SDL, 300SL, 300TD, 300TE, 350SD, 350SDL, 500SL, E300, E320, SL320, SL500

$9.25

107 115 116 123 126 Jack Hole to Floor Jack Adapter

Also W201, W124, R129, W140, W208, W210, W215, W220 - Allows use of floor jack to raise car from factory jack points

I like the convenience of using the factory jack points (holes) but I absolutely DO NOT like using the factory jack - except in cases of emergency road side repair. You all know it can be a little unstable... I solved this problem by using a large heavy duty bolt.

$7.80

Instrument cluster SMALL Bulbs x 4 (Bulb Built Into Holder)

Fits W123W126 W201 W124 W129 Chassis Instrument Clusters

New instrument cluster bulb with socket holder. Sold individually. PLEASE NOTE: This holder is only for the very small warning indicator bulbs, as well as your dash turn signal indicator lights.  It is NOT for the larger bulbs that light your dash at night. 

$39.50

124 Chassis Front Wheel Bearing Kit

Fits 260E 300E 300TE 300CE 300D 300TD E320 E300D 1986 to 1995 - NOT 4-MATIC -- ALSO FITS 107 560SL

 Brand new complete wheel bearing kit. Includes all parts shown for right or left wheel. You with need to order 2 if you want a complete set of wheel bearings for both sides.

$52.75

Later 60x Aluminum Head Diesel Injection Pump Shutoff Valve

201 190D 2.5 - 1986 to 1991 300D 300TD 300SDL 350SD 350SDL - 1990 to 1993 300D 2.5

This is the new Bosch plastic upgrade to replace the old metal style fuel stop solenoid or shutoff valve. This is located on the top rear section of the injection pump (right under the intake manifold). Sorry, no instructions included but it is a straight forward replacement.

$32.50

Later Automatic Transmission Dipstick Genuine

Most models 1981 and to 1993. 123 chassis only Turbo Diesel - see list below

FITS: MERCEDES BENZ 190DT, MERCEDES BENZ 260E, MERCEDES BENZ 300CDT, MERCEDES BENZ 300CE, MERCEDES BENZ 300DT, MERCEDES BENZ 300E, MERCEDES BENZ 300SD, MERCEDES BENZ 300SDL, MERCEDES BENZ 300SE, MERCEDES BENZ 300SEL, MERCEDES BENZ 300SL, MERCEDES BENZ 300TD, MERCEDES BENZ 300TDT, MERCEDES BENZ 3

$8.95

Pencil Glow Plug Reamer 12 mm Special Tool - MADE IN USA

For diesel engines 1980 to 1993 300D 300TD 300CD 190D 300SDL and 1978 to 1985 300SD

When using a pencil glow plug reamer, this modified 12 mm wrench will allow you to PUSH in on the reamer while turning - and let me tell you - this is needed when you have heavy carbon buildup in the prechambers.

$9.95

Engine and Component Assembly Lube

Lubro Moly Brand

High quality lubricant to be used when assembling bearings in engines or in components that are oiled by engine oil. This WILL prevent scoring and wear upon initial start-up after overhaul.

$6.95
Currently out of stock.

Automatic Transmission Nylon Shift Bushing Set of 2

For LATE MODEL (70-73) 108 109 and ALL 114 115 107 116 123 126 201 124 129 and 140 chassis 1968 to 1995

Set of (2). The number one cause of a loose or rattling shift lever is failed or missing shift lever bushings. Our upgraded bushings are made out of nylon and are much tougher than the original plastic type. No instructions or special tools included.

$98.00

124 Late 126 Flasher Multifunction Relay

Fits all 124 chassis 1986 to 1995 and all 126 sedans and SEC coupes 1986 to 1991

This is referred to as the multifunction relay that controls, turn signal, hazard, wiper delay and rear window defroster. If you hare having problems with any of those check fuses first - then suspect relay.

$21.95

Late 114 115 and 116 107 and 123 126 201 124 Seat Belt Warning Buzzer Switch

Fits most 1974 to 1991 Models with steering lock buzzer switch

Genuine MBZ Part with wiring plug for later models: Please note this buzzer is really for the 1985 and later models. The wiring pigtail is not used on pre-1985 steering locks. The switch itself is the same but for older models you will have to install and leave the pigtail connected.

$14.95

All Models 397 Pc. Metric O-Ring Assortment in Case

Must have for any Mercedes D.I.Y.er

This must-have kit does not only have hard-to-find metric sizing, but the o-rings are made out of nitrile which holds up better to heat and is more resistant to oil, grease, hydraulic fluid, silicone and even water.

$8.25

300D 300CD 300TD 300SDL Exhaust Metal Sealing Ring

For Turbo Models Listed above 1981 to 1987

This sealing ring provides seal at the connection of the flexible down pipe and the exhaust pipe going back to the center muffler. This is an upgrade replacement for the older style crushable gasket seal. This all metal ring provides a much more reliable seal over time.

Diesel Fuel Injector Anti Leak Kit w/ Instructions
$9.75

Diesel Fuel Injector Anti Leak Kit w/ Instructions

For sealing all Diesel mechanical injectors 1961 to 1993

We receive a large number of emails from customers complaining about small fuel leaks at the fuel injector housing (coming out the threads between the two halves)and how best to seal them. To fix this high pressure leak requires taking the injector apart and "lapping" the mating surfaces.

$2.50

LATE Bosch CIS 6 Cylinder Fuel Injector to Holder Seal

For 1986 to 1993 M103 6 Cylinder from 061403, all M104 engines with CIS KE-Jetronic Fuel Injection

This is a critical rubber part that seals the fuel injector to the injector holder. Deterioration can result in high idle speeds and poor engine performance. Unless you have a low mileage car with soft seals, these should be changed when testing, cleaning, or replacing your fuel injectors.

Late 107 and 123, 126, 201, 124 Chassis Ignition Switch Only
$54.60

Late 107 and 123, 126, 201, 124 Chassis Ignition Switch Only

Genuine Mercedes Benz Switch - Does not fit all - READ DESCRIPTION CAREFULLY

This GENUINE MERCEDES switch will work on all 107 chassis 380SL and 560SL 1981 to 1989, all 126 chassis sedans and coupes 1981 to 1991 , all 123 chassis 240D 300D 300CD 300TD from 1980 to 1985, all 201 chassis 190E 2.6 and 190D ( 190E 2.3 up to 1988 ONLY) and all 124 chassis from 1986 to 1993.

$9.95

Ultimate Oil Resistant Hi-Temp Reinforced Vacuum hose - 3 FEET

For 1/8 inch vacuum hose connectors on 240D 300D 300TD 300CD 300SD

I have never been impressed with the rubber vacuum hose found on older Mercedes diesels. I don't think the engineers ever anticipated how much abuse or how long these hoses would need to last!

Pages