Search | W124

Displaying 151 - 200 of 514
$30.29

1976 to 1993 C.I.S Fuel Injection 6-Part Video Training Seminar

6 videos total covers both K-jetronic and KE-jectronic fuel injection system theory and testing. Over 2.5 hours of detailed video instruction

It has been over 30 years since the last Mercedes with Bosch C.I.S. fuel injection was manufactured. If you own a 1976 to 1993 Mercedes gas engine with this type of fuel injection, you may have difficulty finding someone to work on your car. In some parts of the country, it may be impossible.

$23.80

Hand Wheel Bearing Packing Tool

You will be amazed how fast and how efficient this tool works!

Flushes Out Old Grease and Repacks Bearings with Less Mess. This Handy Packer works on bearings up to 3 1/2" O.D.

$9.60

Automatic Transmission Inside Pan Protection Magnets x 2

These will work in any automatic transmission from 1968 up to 2004 including the 722.6 transmission. The 7G 722.9 has magnets in it.

Kent is a firm believer in using these strong magnets inside a transmission pan to help extend its useful life. 

They should be placed toward the rear of the pan as shown in the picture below.

$58.75

1976 to 1993 CIS Fuel Injection Pressure Tester Partial "Short" D.I.Y Build Kit

This is a do-it-yourself option. Full kit is available below. For both K-Jetronic and KE-Jetronic 6 cyl. and V/8 engines. Build an ACCURATE tester and save $$.

If you own, plan to own, and want to enjoy driving your old CIS fuel-injected Mercedes, Kent highly recommends you learn to do a full fuel system flow and pressure test.

$59.00

1981 to 1995 722.3 722.4 722.5 New Transmission Pan Replacement w/ Magnets

Fits many models during that period. See complete list below. Late W123, Late R107, W126, W201, W124, R129 and W140

These transmission pans get "out of shape" due to over-torquing the bolts. That crushes the stops (see below), and when that happens, it is very hard to get the pan seal not to leak. Your best option if you are doing a transmission service is to replace the pan.

$8.50

Super Thin 14mm Combination Wrench for CIS Pressure Tester Fittings

For tightening and holding the small adapter fitting that goes into the fuel distributor

When pressure testing your KE-jetronic fuel injection,  you may find you need a really thin wrench to install the small fitting on the right side bottom of the fuel distributor.

On Demand Video
$2.00

How to Repair Old Mercedes Diesel Broken Vacuum Booster Line T Fittings

Part of Kent's $2 tip video collection. The tip will only cost $2 but you could save considerable money and grief by watching this video.

Here is an easy DIY tip to repair a broken vacuum hose nipple on your main vacuum line running from the vacuum pump to the brake booster on the older diesel engines. $2TIP

On Demand Video
$8.00

How to Adjust That Troublesome Little Screw on you 1976 to 1993 C.I.S. Fuel Injected Engine That Won't Run or Run Right

Part of Kent's $8 troubleshooting and repair video collection. The video will only cost $8 but you could save $ hundreds and much grief by watching this video.

This video applies to both K-jetronic and KE-jetronic fuel injection engines on Mercedes from 1976 to 1993.. Let's say you just acquired an old gas engined  Mercedes and you just can not get it to run right and or even get it to start.

Sale
$120.00

Early M119 V8 Spark Plug Wire Set

For those V8 engines with two distributors. High Quality aftermarket set with performance wires. Made in Canada.

Very nice set with silicone copper core wires. See detailed pictures below. Two coil leads of different lengths included. Check before ordering as this fits these models from the early 1990s with dual distributors in the front of the engine. 400E. 400SE.

$32.00

M119 V8 Bosch Spark Plug Set (8)

These are the correct copper core spark plugs for M119 V8 engines from 1991 to 1998

These are the best and only spark plugs you should put in your M119 engine. Hard to find. F 8DC4 

$6.00

Tall Shoulder Inside Short 13 mm 12 Point 3/8 in Drive Sockets x 2

Who doesn't need an extra 13 mm? Quality U.S.A. made. You will love the tall internal shoulders for ease of use.

Nice to have a few extra 13mm sockets around. This is the first tool that gets lost when working on old Mercedes. The tall shoulder inside helps to hold the nut or bolt in a position to make it easier to start the threads.

$38.00
Currently out of stock.

Older Mercedes Maintenance Special LONG Wrench Set

10mm - 13mm - 14mm - 17mm are the most common fastener sizes and these are unique for special uses.

ONLY ONE SET AVAILABLE. Three of these wrenches are made by Gearwrench. You get a very long standard combination 13mm wrench, a long 10mm with a racheting box, a very long 17mm with a ratcheting box, and finally, a very long 14mm combination wrench made by Urrea.

On Demand Video
$16.99

How to Test the EHA Valve on Bosch KE-Jetronic Fuel Injected Engines - On Demand Video

Factory training manual procedure followed step-by-step. You will be surprised by what Kent found on this 560SL engine.

In this 13-minute CIS training video, Kent will walk you through the steps recommended by Mercedes Benz to fully test the operation of the EHA valve on 1984 to 1993 4, 6, and 8-cylinder engines with KE-jetronic fuel injection.

$52.00
Currently out of stock.

KE-Jetronic Fuel Injection Troubleshooting Multimeter w/ Special Attachments

Free on-demand video included on testing the EHA valve and related circuits. Kent believes this is the best tester for the buck.

This high-quality meter can test all types of automotive electrical circuits, but Kent has discovered it is particularly well suited for testing Bosch KE jetronic fuel injection components on those CIS models from 1984 to 1993. Extra adapter fittings are included as shown.

$12.80

Black Plastic Oil Filler Cap Wrist Saver

For many models from 1986 up through 2006. Why is it soooo hard to get these oil caps off!!!

Kent finally got so frustrated trying to get these oil caps off that he came up with this new tool he chose to call the wrist saver. Watch the video to see this unique tool in action.

$8.00

Electric Fuel Pump Electrical Wiring Boot - Set of 2

Used on most electrical fuel pumps from 1976 to 1993. Also used on some cold start injectors.

Often rotten and torn. Replace with new when working on your fuel delivery system. PLEASE NOTE: These are included when you purchase any of our fuel pump delivery kits. 

On Demand Video
$6.99

Bosch CIS Training Series 6: Finding Follow-up Information to Help Interpret Test Results

For 1976 to 1993 Mercedes with gasoline fuel injected 4, 6, and 8-cylinder engines

After completing the pressure test on your CIS engine, you discover a problem. But how can you find out how to isolate and fix it? This is going to require some research on your part. Start by learning how the system works and how each component plays a part.

On Demand Video
$14.99

Bosch CIS Training Series 5: How to Hook Up and Test KE-Jetronic Fuel Pressure

For 1976 to 1993 Mercedes with gasoline fuel injected 4, 6, and 8-cylinder engines

In this video, you will see how the gauges are hooked up to a 560SL and how the pressures are read.  The length of this 30-minute shows the detail Kent has put into filming all the critical components of doing a KE-Jetronic fuel system pressure test.

On Demand Video
$14.99

Bosch CIS Training Series 4: How to Hook Up and Test K-Jetronic Fuel Pressure

For 1976 to 1993 Mercedes with gasoline fuel injected 4, 6, and 8-cylinder engines

This video is specific to K- jetronic fuel-injected engines from 1976 to 1985. This includes the 350, 450, and 280 engines in the R107, W116, W123, and early W126 gas Mercedes. In this 29-minute video. Kent will show you how to hook up the gauge, run the fuel pumps, and complete the test.

On Demand Video
$12.99

Bosch CIS Training Series 3: How to Do Preliminary Fuel Flow and FD Leak Tests

For 1976 to 1993 Mercedes with gasoline fuel injected 4, 6, and 8-cylinder engines

There are a few factory recommend procedures and tests you should do before you do an actual pressure test on a CIS fuel-injected engine. In this 20-minute training video, Kent will walk you through these procedures step-by-step.

On Demand Video
$10.99

Bosch CIS Training Series 2: Options to Get Fuel Pumps to Run with Engine Off

For 1976 to 1993 Mercedes with gasoline fuel injected 4, 6, and 8-cylinder engines

To do proper system testing on CIS fuel injection, you must find a way to get the fuel pump or fuel pumps to run continuously without the engine running. This can not be done by just using the ignition key. In this 15-minute training video, Kent will show the options available to do this.

On Demand Video
$6.99

Bosch CIS Training Series 1: What’s Needed to Test K-Jet and KE-Jet Fuel Pressure

For 1976 to 1993 Mercedes with gasoline fuel injected 4, 6, and 8-cylinder engines

This video will help you decide if you want to try to do a fuel pressure test yourself. It is a fairly simple DIY job but will all the confusion and misinformation on the internet; one would believe it is a complicated process that is hard to understand.

$24.50

Brake Master Cylinder Air Bleeding Kit with FULL Video Instructions

This bleeder kit is primarily for bench bleeding in a vise but can also be used to bleed an air-locked master cylinder on the car. Custom wrench included.

This procedure is a must do anytime you install a new master cylinder or allow fluid to completely leak out of your master cylinder.

On Demand Video
$10.99

Master Cylinder Removal, Bench Bleeding, and Replacement Instructions - On Demand Video

Covers most master cylinders 1968 to 1995. Learn to do it right with minimal loss of fluid and mess.

In this 30 minute instructional video Kent will use a 1972 300SEL 4.5 to show you how to remove the master cylinder with minimal spillage, how to install the tank and bench bleed a new master cylinder, and how to reinstall it with minimal brake fluid spillage while protecting your car's paint. 

On Demand Video
$4.99

How to Test Your Fuel Accumulator - ON DEMAND VIDEO

Has your rear-mounted fuel accumulator failed on your 1976 to 1993 K-Jetronic or KE-Jetronic fuel system

In this 9 minute instructional video, Kent will explain how to test your fuel accumulator to determine whether or not it has failed internally. A failed accumulator will make your engine hard to start when hot.

$16.75

W116, R107, W123 and W126 Tail and Running Light Bulb Assortment

Fits almost all models from 1973 to 1991. Assortment of 14 bulbs. Name brand Hella, Osram, or Phillips bulbs

Assortment includes 6 single-element brake and turn signal bulbs, 4 dual-element bulbs for the front marker lights, and 4 small tail light bulbs. Good idea to carry this assortment in the trunk of your car. 

$24.80

20 Piece Interior Light Bulb Replacement Kit

For most Mercedes from the Mid 1970s to the Early 1990s

Assortment of new interior bulbs as shown. These light up your dash, center console, glove box and shifter ( on some models).

Assortment includes the following:

Sale
$120.00

OM617 Turbo Diesel Intake and Exhaust Valve Set w/ Extras - USED

For 1978 to 1985 300SD and 1981 to 1985 TURBO 300D, 300CD and 300TD

Good used set of valves for OM617 turbo cylinder heat. Includes all parts as shown (valves, springs, rotators, and spring caps. 10 THIN adjusting nuts INCLUDED. No valve cap nuts. Only parts shown in the picture are the actual items you will receive.

$6.80

Fuel Tank Screen Seal 0-Ring Genuine O.E.

Fits most fuel tank filter screens from 1973 to 1995 All W116 R107 W126 W123 W124 and W201

New Mercedes o-ring as shown. Always replace this seal when removeing and cleaning your fuel tank strainer ( screen ).

$5.80

8mm ( 5/16 inch ) Fuel Hose End Pugs x 4

Use when disconnecting a fuel hose to prevent spillage on your engine or floor!

You would be amazed at how much fuel can leak out of a fuel hose when you disconnect it from your tank or engine. This is an easy way to prevent messy spills.

$4.75

All Models Radiator Hose Chafe Protector - Heavy Duty

Don't let a hose rub up against the engine or radiator. Easy install with zip ties included if needed.

This is a great solution to what is sometimes a nagging problem. This heavy duty and flexible and adjustable plastic spacer can be put on the top or bottom radiator to prevent chafing in and area where it might come in contact the the engine or the radiator.

$39.75

1972 to 1987 Bosch Long Diesel Fuel Injector Critical Replacement Parts - Used

Other than the nozzle itself, these are the critical parts that wear out internally and can cause leaks and misfiring.

When “rebuilding” an old Bosch mechanical fuel injector, replacing the nozzle is usually enough get it working again at peak performance. But sometimes you will run into a fuel injector that just won't fire right nor product a correct fan spray pattern.

$105.00

1968 to 1987 4, 5 and 6 Cylinder Diesel Engine Prechamber Removal Tool

61x tool: For OM615, OM616, OM617, and early OM 601 and OM603 through 1987 only.

Version 4 update 2/22: New color and style but still does the same job. This is one of the key tools you will need to remove stubborn pre chambers from the cylinder head of your old diesel engine.

$19.00

40 Piece Silicone End Cap and Plug Set - Amazing Uses!

Push them over a hose and they act like a sealing end cap. Turn them around and push into a hole to act as a plug. Cut in half - use one piece for a splice between hoses.

We starting using some of these to plug brake lines while changing out calipers. Then we started using them on fuel and oil hoses. Now we are using them all over the place and keep finding new uses for them on a monthly basis. These are a MUST HAVE! Watch the video below to become a believer!

$18.75
Currently out of stock.

5th Generation LED RED Instrument Light Bulbs x 2

For W123, W126 and W201 chassis. Built in heat sink and non-polarity wiring. Watch the videos below!

This is the newest LED light bulb Kent has found and tested that you can install on the backside of your instrument cluster to increase your instrument lighting on your older Mercedes. These particular bulbs will be much brighter with a VERY RED cast light and they don't get hot!

$8.45

Loctite Metal Flange Gasket Maker - Small Tube ( 6 ml )

Very best sealant for differential covers and other flat mating surfaces that do not use a gasket. Will not deteriorate like silicone RTV

Here is my all-time favorite gasket maker and sealant. You may already know how I feel about RTV silicone products (I think they should be outlawed!). We have had a number of our customers ask us where to get this so we decided to offer it on our website.

On Demand Video
$9.99

Repair Leaking Chrome Alloy Wheels with Miracle Paint - On Demand Video

Use multiple coats of Miracle Paint to stabilize and fill the corrosion that causes the tires to leak.

In this video, Kent will show you how he fixed his leaking tires on his chrome alloy wheels by using Miracle Paint. This is a full 22-minute step-by-step instructional video. Watch the video "trailer" below to give you a better understanding of what is involved in this procedure.

$40.95

Rust and Corrosion Small Pit Filling and Leveling Kit w/ BLACK H.D. Miracle Paint

Use Multiple Coats of Miracle Paint and Sand Between Coats to Stabilize and Level - Ideal for Leaking Chrome Wheels and Surface Rust Pitted Steel

This kit was developed by Kent primarily to fix leaking chrome wheels. The free on-demand video that comes with this kit shows the detailed process of cleaning and filling the corroded areas along the edges of the inside of the wheel to seal them and stop annoying tire leaks.

$399.00

6 Cylinder M103 M104 CIS Fuel Delivery FID Overhaul Kit

For 1988 to 1993 M103 and M104 CIS powered cars (W201, W124, R129 and W126 chassis)

Most 1988 to 1993 6 cylinder CIS fuel injection delivery (FID) systems are old and tired and have not been properly maintained. These include the W201 190E 2.6, the W124 260E 300E, 300CE, 300TE, the W126 300SE, and 300SEL, and the R129 300SL.

$4.20

Diesel Compression Tester Replacement Sealing Washers

You will need extras if you plan to do multiple compression tests

When doing a compression test you must properly seal the inner surface of the pre-chamber with the fuel injector hole adapter. Copper washers work the best for this to ensure a 100 percent seal. Do not use the engine's heat shield washers.

$16.75

5th Generation LED AMBER Instrument Light Bulbs x 2

For W123, W126 and W201 chassis. LOW heat and non-polarity wiring.

Kent has found and tested this newest LED light bulb that you can install on the backside of your instrument cluster to increase your instrument lighting on your older Mercedes. These particular bulbs will be much brighter with a more AMBER cast light, and they don't get hot!

Pages