ALERT: Miracle Paint is back in stock! CLICK HERE to order.
This is the newest LED light bulb Kent has found and tested that you can install on the backside of your instrument cluster to increase your instrument lighting on your older Mercedes. These particular bulbs will be much brighter with a white light and they don't get hot!
This video will show you how to remove the front crank seal race using the factory tool and using Kent's custom puller. It will also demonstrate a very easy way to install a new replacement race before installing a new seal.
Those old hardened and discolored plastic fuel hoses in your diesel engine compartment probably need to be replaced. When they crack and break you can dump a ton of fuel out on the road before your engine quits and leaves you stranded.
Kent has found and tested this newest LED light bulb that you can install on the backside of your instrument cluster to increase your instrument lighting on your older Mercedes. These particular bulbs will be much brighter with a more yellow cast warm white light, and they don't get hot!
This 17-minute video will cover the removal of an old Hirschmann power antenna and then Kent will show you how to troubleshoot the wiring plug in the car to see if you are getting proper power back to the antenna. No sense in replacing a faulty antenna until you make sure your wiring is OK!
This will hold the top of the strut and keep it from turning when removing and installing the 22mm nut.
In this 28-minute instructional video Kent with show you how to do a compression test on your own Mercedes gas engine and explain how to interpret the results. It is very important you do this procedure BEFORE "throwing" parts at your engine trying to fix a performance problem.
Doing a compression test is one of the best ways to determine the internal health of your gas engine. This is a primary test for doing a physical examination. You want to do this on any old Benz before spending a lot of money to get the engine running right or before restoring your car.
You might be surprised to realize you spark plug holes need cleaning - and yes some REALLY need cleaning! This 5-minute video will demonstrate Kent's method of cleaning the threads in the cylinder.
Whether your just changing pads, hoses, or doing a complete brake system overhaul, the items we include in this DIY will guarantee the job gets done with no mistakes, minimum frustration, and lasting results. There is no other kit like this anywhere.
This manual is a complete guide for all brake component replacement for all 1965-1995 Mercedes Benz cars. It will help you identify common signs of trouble, inspecting brake components, and replacing major brake components - a necessity for any DIY brake job on your Mercedes Benz!
In this 22-minute instructional video, Kent will take you inside the door on a W123 240D and show you all the key points that should be lubricated and the type of lubricants you should use.
This is a very common problem on the W123. The wood will just fall off someday. Worse when the car is left outside or in a hot climate.
This on-demand instructional video was filmed to go with Kent's new fuel tank sending unit service kit launched in June of 2020. This is not a complete video on the subject of fuel level sending units. For the complete video see related products below.
If your fuel gauge stops working or is not reading accurately, many times it can be repaired by removing it from the fuel tank, taking it apart and giving it a good internal cleaning of the contact points, float shaft, and wires.
We have been talking about this for years. It was Ryan who got a friend to make this for us. It is a very high-quality vinyl with a special stick adhesive that "breathes" and does not allow bubbles to get trapped during application.
This 23-minute video will demonstrate how Kent repairs some small rust spots inside the fender wells of a W116 sedan. Disclaimer: This method of repair is not recommended for large rust holes under the car or for holes that have been caused by road salt.
When the motor won't move the window down you can not get to the bolts that hold the regulator to the glass. So then how can you get it out of the door! What a pain! In this xxx minute video Kent will show you what you need to do in order to get a "stuck" power window regulator out of a door.
Fuses, supplies, and video instructions (below) to restore most older fuse boxes to better than original condition.
Fuses, supplies, tools and video instructions (below) to restore most older fuse boxes to better than original condition.
Hard to believe we took so long to come up with this tool. It was Gerson's genius that made it happen. The secret turned out to be the hook that keeps the tool in place while stretching out the rubber donut. Wow! What a cool tool.
Socket is now black (impact grade). This is a tool that Kent first thought about making 20 years ago. While installing shock absorbers in his 380SL he had finally had enough - so it was back to the machine shop to come up with a new tool.
In this video, Kent will show you how to safely and cleanly remove the fuel from the tank on your older Benz. You will need to drain the fuel anytime you replace the back end hoses, the tank filter screen, the fuel pump or the fuel filter.
Hard to believe we took so long to come up with this tool. It was Gerson's genius that made it happen. The secret turned out to be the hook that keeps the tool in place while stretching out the rubber donut. Wow! What a cool tool.
This is a hard-to-find adapter that will need if you have one of the early 1990s 5 and 6 cylinder turbo diesel engines. We machine this right here in our shop and it is designed to work directly with our OM61x compression tester ( see related products below):
Have you ever had a hard time finally a very small coolant leak? Do you find yourself adding small amounts of coolant but can not see any leak? Is there a funny smell coming from inside your Benz when you run the heater?
In this video, Kent will walk you through the steps needed to convert your older Brake Bleeder tank to one that can continue to bleed brake systems as well as pressure test radiators and cooling systems.
Many uses for this quality hard steel tool including removing W123 and early W126 motor mount bolts.
This is a "must-have" kit when adjusting release "pop" pressures on older diesel mechanical fuel injectors. It is the internal spring "shim" thickness that determines the exact pressure required for the release of fuel at the tip of the injector.
This tool will allow you to remove a cylinder head pre-chamber on a 1990 to 1991 350SD 350SDL (126 chassis), 1990 to 1993 300D 2.5 (124 chassis), and 1992 to 1995 300SD / S350 (140 chassis). The special black fitting attached to the slide hammer is custom made in our shop.
On a regular basis, Kent and Gerson custom make tools to make certain jobs go easier and faster. So is the case with this long reach ratchet. It was developed to get glow plugs out of the older diesel engines without having to remove the hard lines.
You will receive two (2) five liter bottles more than enough to do a full oil change on any vehicle:
If you acquire an older Mercedes diesel and want to test those large Bosch injectors with your V3 gasoline bench tester, you will need 4 things to complete the conversion: 3000 PSI gauge, our new capture bottle to hold the larger injectors, injector sealing kit, and Kent’s written manual and vid
Published in August of 2019, this has been one of the most requested videos over the past two previous years.
This video will not only save the condition of your door panel, but it will save you a lot of time and frustration when you go to replace a door panel after doing maintenance inside your door. Those old plastic film liners always seem to be torn, ripped, and downright ugly.
We know that many of you own multiple Mercedes, including both gas and diesel models. If you own one of Kent’s fuel injector pressure testers you no doubt will want to test all your applicable mechanical fuel injectors in both types of older engines.
In this short video, Kent will give you an overview on setting up and using Version 3 of his bench mount CIS gasoline injector pressure tester.
This video is specifically for setting up and using Kent's newest version of his diesel fuel injector bench mount tester. It does not contain any information on the actual process of cleaning or rebuilding a fuel injector.
This is one set that will pretty much do it all: door panels, radio, windows, interior trim, exterior trim, engine, fastener plugs, seals, etc. Strong enough to even change a bicycle tire...
UPS ground shipping only. Can not be shipped internationally. Rather than try to explain what this kit does and how it does it we are going to ask you to watch the video below if you have not already done so.
This video is part of the full net repair kit we sell. See related products below. If you choose just to watch this video, you will have to source your own bungee cord and crimping sleeves.
This is the very best hose Kent has found to use to install spark plugs in restricted spaces. Watch the video below and he will demonstrate.
This on demand video only covers the principles of how to get a non-memory power seat in a 1980 to 1990 Mercedes to move forward and backward so you can get to the bolts to remove the seat from the car or remove the seat spring from the track assembly.
Keeping your throttle linkage ball sockets and pivot points lubricated extends the life of the parts and maintains top performance for the engine as well as some of the later transmissions.
This video will show Kent's technique on how to prime and paint alloy wheels using our wheel paint kit and masking dam that we sell separately. See below. The techniques will also apply to any spray can paint you should choose to use.
Want the best, fastest, and easiest way to polish faded anodized aluminum trim, to remove fine scratches from your glass, to loosen rusted and stuck fittings and bolts, and to sand rust out of tight places? - enter the multitool or multi-function tool.
This is a full 25-minute step-by-step instructional video on how to properly flush or bleed your brake system using our pressure brake bleeder and fluid capture tank.
If you already have a multi-function tool or you plan to buy either our glass or anodized aluminum polish kit ( see below ) you really don't need a second tool unless you want to dedicate one just for "banging" on rusty fittings and bolts. We offer this same kit with the tool included.
In this video, Kent explains the correct procedure for cleaning and lubricating your hubs and rear brake rotor BEFORE you install your wheels. He hardly ever sees this done when removing wheels on 15 plus-year-old Mercedes so he knows it is almost ALWAYS neglected.
This tank works amazing! Put in the heavy rear end or trans fluid. Pump up the pressure. Stick the non-fall-out end in to fill hole... and just push on the valve in the handle of the filling wand.